Clifford Responder LE 3.3X страница 54 Скачать руководство пользователя

Страница: 54 / 56

Remote Start

Press

. Remote start LED blinks for 3 seconds and remote start

tone sounds.

Rear Defogger

Press four times, and then press

(only after remote start is

ON.) Remote start LED turns ON, and you will hear 1 beep.

To disable the remote start system

Move the shutdown toggle switch to the OFF position.

Location of Shutdown Toggle Switch___________________

Valet Mode

Press two times and then

3
4
5
6

A U

. The UNLOCK LED and Function

LED blink and remote beeps one time. When valet Mode OFF, the

remote beeps two-times.

Valet take over

Before turning off the engine, press and release

. within 3

seconds. Then wait a few seconds.

Turn the ignition key to the OFF position.

The engine will remain running until the programmed time elapses

or a shut-down input is received.

Location of Valet button_________________________________

▀

Cut along dotted line and f

old f

or a quick and eas

y r

efer

ence to k

eep in pur

se or w

allet

✂

Содержание Responder LE 3.3X

























































Результаты поиска

Содержание Responder LE 3.3X

Отзывы:

Похожие инструкции для Responder LE 3.3X

Бренды по названию

Популярные бренды

Clifford Responder LE 3.3X, Руководство пользователя

Результаты поиска

Содержание Responder LE 3.3X

Отзывы:

Похожие инструкции для Responder LE 3.3X

Бренды по названию

Популярные бренды