Clifford Responder LE 3.3X Скачать руководство пользователя | Manualshive

Страница: 4 / 56

background image

© 2008 Directed Electronics—all rights reserved

iv

Government Regulations

This device complies with Part 15 of FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interfer-
ence, and (2) This device must accept any interference received, including
interference that may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television, which can be determined by turning the equipment OFF
and ON, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

This device complies with the Industry Canada Radio Standards Specifica-
tion RSS 210. Its use is authorized only on a no-interference, no-protection
basis; in other words, this device must not be used if it is determined that
it causes harmful interference to services authorized by IC. In addition, the
user of this device must accept any radio interference that may be received,
even if this interference could affect the operation of the device.

Warning:

Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this device.

«
...
2
3
4
5
6
...
»

Содержание Responder LE 3.3X

























































Отзывы:

Нет отзывов

Похожие инструкции для Responder LE 3.3X

Бренд: Zodiac Страницы: 12

iDual A E27 iD60

Бренд: jedi LIGHTING Страницы: 23

Бренд: Rac Страницы: 5

Бренд: Gira Страницы: 7

Fireball Taurus

Бренд: Escient Страницы: 39

Бренд: Lexicon Страницы: 34

PURSUIT PRO9276TW

Бренд: Audiovox Страницы: 8

Бренд: Orolia Страницы: 20

2.4GHz FHSS Radio System

Бренд: EScale Страницы: 12

Multi-Channel Remote Control

Бренд: Heath Zenith Страницы: 12

Бренд: Cobra Страницы: 3

Бренд: Chamberlain Страницы: 4

RCR504BR Series

Бренд: RCA Страницы: 3

Бренд: Manfrotto Страницы: 3

Бренд: Universal Страницы: 19

Бренд: MFJ Страницы: 4

Бренд: CoCo Страницы: 7

Бренд: DuoFern Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды