Clifford Responder LE 3.3X Скачать руководство пользователя | Manualshive

Страница: 36 / 56

background image

© 2008 Directed Electronics—all rights reserved

0

Timer mode

To activate the runtime of the vehicles engine during remote start:

1.

Press the button two-times and then .

2. The vehicle will confirm with 4 fast parking light flashes.

3. The system will start every 3 hours until canceled by the brake,

hood, or neutral safety shut-down wires. The remote will respond

with the Start and Stop remote start notification during each Start

and Stop of the Vehicle while in Timer mode.

Important!

Timer Mode should be used only in open areas. Never

start and run the vehicle in an enclosed space such as a garage or

carport.

To exit timer mode, Press the button two-times and then again.

Turbo timer mode

Turbo timer mode keeps the engine running after arriving at your

destination for a programmable period of 1, 3, 5 or 10 minutes. This

allows the system’s timer to conveniently cool down the turbo after

you have left the vehicle.

Transmit the timer mode feature with the remote while the engine is

running, press two-times and then . After exiting the vehicle,

arm the alarm and the vehicle will remain running for the programmed

runtime. (The remote start feature is still enabled).

The system monitors the engine speed and will automatically shut the

engine off if the RPMs rise above or fall below the programmed levels.

This feature prevents damage to the motor due to fuel delivery system

failures or other problems which may cause the engine to race.

Note:

To enter turbo timer mode with a manual transmission, perform

the manual transmission procedure (See p.29), with the door open.

«
...
34
35
36
37
38
...
»

Содержание Responder LE 3.3X

























































Отзывы:

Нет отзывов

Похожие инструкции для Responder LE 3.3X

Бренд: Absaar Страницы: 36

Бренд: Jabra Страницы: 18

Бренд: YMGI Страницы: 8

Бренд: Chicago Pneumatic Страницы: 88

Бренд: REMdevice Страницы: 14

Room Air Conditioners Remote Controller

Бренд: Heat Controller Страницы: 10

Бренд: Yolink Страницы: 32

Бренд: FUTABA Страницы: 2

Бренд: Pioneer Страницы: 7

Бренд: DeDietrich Страницы: 112

Бренд: F1 Страницы: 176

Бренд: Louvolite Страницы: 2

Бренд: INIM Electronics Страницы: 12

Бренд: KYUNG IN ELECTRONICS Страницы: 5

KID-05.1 S KID-05 S

Бренд: Kaysun Страницы: 16

Бренд: RED FUEL Страницы: 11

Бренд: Solace Страницы: 28

Бренд: YoungShin Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды