background image

© 2008 Directed Electronics—all rights reserved

Safety features 

This system has several important safety features to ensure proper 

operation of the motor and prevent accidental damage to the engine or 

its components.

Starter anti-grind circuitry

Whenever the vehicle is remote started, advanced anti-grind circuitry 

prevents the starter from engaging, even if the key is turned to the 

start position. This prevents damage to the starter motor if the key is 

turned to the start position during remote start operation.

Note: 

Anti-grind circuitry only works when the remote start 

system is operating the motor and the Failsafe® Starter Kill relay 

is installed.

Disabling the remote start system

This feature allows the remote start unit to be temporarily disabled 

to prevent the vehicle from being remote started accidentally. This 

feature is useful when the vehicle is being serviced or stored in an 

enclosed area. 

To disable the remote start, move the shutdown toggle switch to the 

OFF position. Check with your installer for the location.

Location of Shutdown Switch____________________________

Содержание Responder LE 3.3X

























































Отзывы: