manualshive.com logo in svg

Clifford Responder LE 3.3X, Руководство пользователя

Поделиться
Скачать
Clifford Responder LE 3.3X Скачать руководство пользователя страница 37

© 2008 Directed Electronics—all rights reserved

Cabin temperature

Using the Responder LE system, you have the ability to check the 

temperature inside the vehicle. 

Press the   button once and then hold until the remote beeps, and 

then release. The LEDs on the remote will light up indicating what the 

temperature range of the vehicle is. 

95˚F and above 

76˚F to 95˚F  

56˚F to 75˚F  

32˚F to 55˚F  

32˚F and below  

Rear defogger

The rear defogger (if connected) is programmed to automatically acti-

vate when remote start is turned on. If the interior cabin temperature 

is above 55˚ F the defogger will not activate. 

To manually activate the rear defogger after remote start is on:  

Press  four times, and then 

 . 

Valet take-over

The Valet take-over feature allows the vehicle to remain running after 

the key has been removed from the ignition. This feature is useful for 

occasions when you wish to exit and lock the vehicle for short periods 

Содержание Responder LE 3.3X

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды