background image

INSTRUCTION 

m

m

.  A800-7425 J (Page 1 of 16)

1.0 GENERAL INFORMATION

1.1

RECEIVING AND UNPACKING

Handle and unpack the equipment carefully.

Operating Conditions

Immediately upon arrival, check the shipment against the
packing list. Any damage should be reported
immediately to the carrier and to the nearest CMC
representative.

Equipment which will not be installed immediately should
be stored in a clean, dry location. Precautions should be
taken to prevent moisture, dust and dirt from
accumulating in storage and installation areas.

1.2

SPECIFICATIONS

Electrical

AC Supply

- 100/115/230VAC ±10%,

50/60Hz,  Jumper selectable

Input Power

- 15 VA

Transducer
Excitation

- 5.6 VDC

Tension
Output Signal

- 0-10 VDC, 5 mA

Conditioned

- 0-10 VDC, 5 mA or adjustable

Tension Output

0-2 VDC, approximately 2K

Signal

Ohm output impedance

Calibration

- Full scale range of 8:1

TLD Output

- 1 N.O. & 1 N.C. 5 Amp,

Contactor

250 VAC resistive (each limit)

(Optional)

Isolation

- 0-10 VDC, 5 mA or 4 to

Amplifier

20 mADC, 1500 VRMS

(Optional)

(2000V peak) isolated

Ambient
Temperature

- 0-40

E

C  (32-104

E

F)

Relative
Humidity

- 5% to 95% (w/o condensation)

Altitude

- to 6600 Ft. (2000 meters)

Weight

Enclosed Indicators - 12 Lbs.

Open Panel
Indicators

- 3 Lbs.

1.3

DESCRIPTION

The indicators are assembled from modules as shown in
Figure 1 on page 2. The modular approach improves
versatility by increasing the combinations of features
available.

1.3.1 Circuit Boards - There are two circuit boards
available.

    - Standard Circuit Board
    - TRL Circuit Board

The Standard circuit board amplifies the signals from the
transducer(s) and provides a tension output signal which
represents  the total tension measured by the
transducers.

The TRL circuit board independently amplifies the
signals from each of two transducers, the left transducer
and the right transducer of the sensing roll. There are
three tension output signals from this circuit board, one
for the left transducer, one for the right transducer, and
one for the total of the left and the right.

Содержание Cleveland-Kidder TMI



















Отзывы: