Clarke 6500690, Инструкция по эксплуатации и обслуживанию

Страница: 6 / 36

6
WARNING: The use of any accessory, or attachment, other than those recommended in this manual, may
present a risk of personal injury.
HAVE YOUR TOOL REPAIRED BY A QUALIFIED PERSON: This electric tool is in accordance with the relevant
safety requirements. Repairs should only be carried out by qualified persons using original spare parts,
otherwise this may result in considerable danger to the user.
SAW BLADES: Do not use saw blades which are damaged or deformed. Use only saw blades recommended
by the manufacturer which conform to EN847-1. Take care that the selection of the saw blade is suitable
for the type of wood to be cut which meets the requirements on page 4. Do not use High Speed Steel
(HSS) blades. Use only saw blades for which the maximum possible speed is not less than the maximum
spindle speed (no load speed) of the table saw and the material to be cut.
USE THE BLADE GUARD: Make sure that the blade guard moves freely on its pivot point and that the front of
the guard is always in contact with the saw table when not cutting. Always use the blade guard and riving
knife for every operation.
IMPORTANT: THIS SAW IS NOT DESIGNED FOR NON-THROUGH CUTTING OPERATIONS
SUITABLE MATERIALS : Do not use the saw to cut materials other than wood.
PROVIDE ADEQUATE SUPPORT FOR LONG WORKPIECES: Provide adequate support to the rear and sides of
the saw table for wide, or long pieces of work. Saw horses or similar devices should be used to prevent the
ends of the workpiece from drooping.
COMPOUND CUTTING: Take care when making compound cuts. If both mitre angles and bevel angles are
to be set for compound mitre cuts, set the bevel angle first. Make sure that the table saw is disconnected
from the mains supply before changing to the required angles.
ASSEMBLY: Do not operate this saw until it has been fully assembled and correctly prepared for use in
accordance with the instructions in this manual.
MIND YOUR HANDS : Keep your hands well away from the blade area at all times. Do not place them in the
path of the blade when operating the saw. Pay full attention when rotating the table. Keep your fingers
well away from the side panels.
WEAR GLOVES: Wear gloves when handling saw blades and rough material. Saw blades should be carried
in a holder whenever practical.
SECURE HANDLES AND CLAMPS: Make sure that all handles, clamps and guards are securely fitted before
operating the saw. Do not perform any cutting operation freehand.
USE THE MITRE GAUGE: Always hold the work firmly against the mitre gauge fence when cross cutting.
USE A PUSH STICK: Use a pushstick to feed the workpiece past the saw blade ensuring it is securely fastened.
The push stick should always be stored with the machine when not in use.
DO NOT WORK FREEHAND: Never perform any operation ‘freehand’ i.e. do not use your hands alone to
support, or guide the workpiece. Always use either the rip fence, or the mitre gauge (as appropriate) to
position and guide the work.
STAY CLEAR : Never stand, or have any part of your body in line with the path of the saw blade. A small cut-
off piece could be caught by the back of the blade and thrown towards the operator. Stand to one side
of the blade. Keep your hands out of the line of the saw blade.
CROSSCUTTING: Move the rip fence out of the way when cross cutting. Never use the rip fence as a cut-
off gauge when crosscutting.
SWITCH OFF: If off-cuts of wood become jammed in the machine, switch off and disconnect from the
mains supply before removal.
STALLED BLADE: If the blade stalls, or stops while cutting, switch off and disconnect from the mains supply
before attempting to free the blade.
RIPPING: When ripping or bevel ripping, always use the rip fence together with the push stick. Never make
these cuts freehand. The blade could bind in the cut and cause a kickback .
REMOVE THE MITRE GAUGE: Remove the mitre gauge from the table during any cutting operations which
involve the rip fence .