Clarke 3110876 Скачать руководство пользователя | Manualshive

Страница: 7 / 32

background image

7

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

COMPRESSED AIR REQUIREMENTS

A typical air line layout is shown below. If an automatic in-line filter/regulator is
used, it will keep the tool in good condition, but should be regularly checked
& topped up with oil. CLARKE air-line oil should be used and the lubricator
adjusted to approx 2 drops per minute.

Use only clean, dry, regulated compressed air as a power source.

Air compressors used with the tool must comply with the appropriate
European Community Safety Directives.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU
ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF
COMPRESSORS AND COMPRESSED AIR SYSTEMS.

«
...
5
6
7
8
9
...
»

Содержание 3110876

































Отзывы:

Нет отзывов

Похожие инструкции для 3110876

Бренд: Jet Страницы: 14

PARKSIDE PPHSS 715

Бренд: Parkside Страницы: 10

Бренд: Et system Страницы: 83

Бренд: Gardebruk Страницы: 34

7 138 02 62 09 0

Бренд: Fein Страницы: 105

Бренд: TSO Products Страницы: 2

FTPC150V12-S-WP

Бренд: POS Страницы: 2

Бренд: Stanley Страницы: 24

Бренд: ATD Tools Страницы: 2

Бренд: Parkside Страницы: 94

Бренд: REED Страницы: 12

Бренд: Bioenno Power Страницы: 16

Бренд: YATO Страницы: 80

Бренд: King Canada Страницы: 5

Бренд: Westward Страницы: 27

Бренд: MasterCraft Страницы: 24

Бренд: Total Страницы: 11

Бренд: Neilsen Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды