27
revised 04/15
Sfc
cartridge Dust collector
5.8.2 SWING DOOR RE-ARMING
INSTRUCTION
ENSURE THAT YOU HAVE THE PROPER CLIP
TYPE FOR YOUR SIZE VENT. FAILURE TO USE
THE CORRECT CLIPS MAY CAUSE VENT TO
FUNCTION IMPROPERLY.
in the event of an explosion or other unforeseen
circumstances, it may be necessary to re-arm the
explosion vent located on your Dust collector. Parts
discussed in this procedure are identified by numbers
that coincide with those shown by a detail drawing and
parts list.
a violent explosion may deform the doors
(7)
(1)
which
will require replacement in addition to the clip hold
downs
(3)
and flat clip supports
(4)
.
Before re-arming a vent where doors are not
damaged:
1. check the flat clip supports
(4)
for flatness. if only
one end is bent, flip or rotate 180°, and reuse. if both
ends are bent, replace. Do not flatten and reuse, as
the operating characteristics of the vent will change.
2. reorder clip hold downs
(3)
and replace. Do not
flatten or reuse clip hold downs.
3. check gasketing. replace if damaged or abnormally
compressed. if vent has been in operation for two
years, replace gasket.
4. Loosen four socket hex cap screws
(17)
on door
compression plate
(8
). remove bent clip hold
downs
(3)
.
5. Loosen nuts
(9)
holding flat clip supports
(2)
on
internal door edge
(7)
. check flat clip supports
(2)
as
directed above. rotate 90° so flat clip support
(2)
is
parallel with the door edge
(7)
.
6. Pull door
(1)
into an almost closed position.
7. Pull door
(7)
against door
(1)
until both doors are
closed and hold. Make sure that both top and bottom
door edges fit under gasket.
8. rotate flat clip support
(2)
90° so that the flat side
is over the edge of the door
(1)
in a perpendicular
position. finger tighten nuts
(9)
.
9. Push new clip hold downs
(3)
into recessed area of
clip support block
(18)
until they stop. Make sure that
the forward edge of the clip hold downs
(3)
are over
the outside edge of the door plate
(5)
.
10. tighten four socket hex cap screws
(17)
.
11. tighten nuts
(9)
. Make sure the flat clip supports
(2)
remain perpendicular to the edge of the
doors
(7) (1)
.
12. release handle. explosion vent is now rearmed.
6. TROUBLESHOOTING GUIDE
use the troubleshooting guide to correct any
problems that occur with your dust collection unit.
if the problem or condition continues, contact the
uaS customer service office.
all electrical/mechanical troubleshooting should be
performed by a qualified electrician/maintenance
individual familiar with uaS equipment.
Prior to troubleshooting any equipment, read the
installation and operation Manuals for each piece
of equipment to be serviced.
!
WARNING
CAUTION
Содержание UAS SFC Series
