CLARCOR UAS SFC Series, Руководство пользователя

Страница: 16 / 40

11
revised 04/15
Sfc
cartridge Dust collector
Disconnect lifting slings and spreader bars used for
installation.
apply sealant to the next hoppers that will receive a
filter module (refer to figure 7). apply sealant to the
side bolting flange of the next filter module to be
installed using the “figure 8” pattern (refer to figure 7,
Detail B). Place this module on its hopper. use the
hardware provided (refer to figure 7, Detail B).
Place this module on its hopper. use the hardware
provided (refer to figure 7, Detail B) and bolt the
module sections together. Bolt the filter module to
the hopper (refer to figure 7, Detail a). Securely tighten
all hardware at the filter module and hopper. recheck
leg assembly sway braces to ensure they are tight.
install fasteners (bolt, flat washer, lock-washer, nut) to
all four pry locations..
Disconnect lifting slings and spreader bars used for
installation.
repeat this process until all the module sections are in
place, securely fastened and anchored to the foundation.
recheck all hardware connections to make certain they
are securely tightened. remove lift slings and spreader
bars and clear all tools from the work area.
NOTE: Make certain all bolts (including the anchor
bolts) are properly tightened before proceeding
with the remainder of the installation.
install all cartridge filters removed at the beginning
of the installation process and install the filter access
doors (refer to Section 5.1).
3.4 ELECTRICAL INSTALLATION
ELECTRICAL SHOCK HAZARD
all electrical work should be performed by a
qualified electrician in accordance with local
electrical codes. Disconnect electrical power before
installing or servicing any electrical component.
GENERAL
Several types of standard electrical components can
be installed to control and monitor your dust collector.
a VfD or a motor starter circuit (combination starter
panel) is required to safely start and stop the system.
a properly sized circuit breaker or fused disconnect
is also required to safely work on and service the
electrical system. in addition, a 115/1/60 (2 amp)
control circuit is required for the pulse control panel.
Some or all of the above items may be included in the
controls package you purchased from uaS. any one
of the following control combinations can be used:
• Motor starter with Digital Pulse Monitor (DPM) for
continuous pulse cleaning.
• Motor starter with Digital Pulse Control (DPC) for
on-demand pulse cleaning.
• VFD with DPM for continuous pulse cleaning.
• VFD with DPC for on-demand pulse cleaning.
refer to uaS sales order to verify the control
configuration purchased with your unit and whether
additional items are required to control and operate
your system.
3.4.1 MOUNTING THE CONTROLS
Mount the VfD or combination starter panel for the
fan motor in a convenient location. it is recommended
that these controls be mounted on a wall or pedestal
in an area subject to minimal vibration and electrical
noise. Mounting hardware is provided by the
customer or the contractor. if the panel includes
the DPM or the DPc gauge and uaS timer control
board, then the location of the panel must within close
proximity of the dust collection unit as shown in figure
8. for additional setup and installation information
refer to the VfD and/or DPM/DPc owner’s Manuals
provided.
avoid mounting the panel on the collector due to
vibration generated from blower assembly and the
pulsing system.
for all pulse control panels, connect the black plastic
pressure tubing (25’ [7.5 meters] provided by uaS) to
the panel fittings and the Sfc unit. connect the dirty air
plenum of the Sfc to the high pressure port (dirty air)
on the panel as shown in figure 8. connect the clean
air plenum of the Sfc to the low pressure port (clean
air) on the panel.
3.4.2 SOLENOID VALVE ENCLOSURE
WIRING
the solenoid valves at the dust collector must be
wired correctly to the pulse control panel. refer to
figure 9 when making connections from the pulse
control panel to the solenoid valve enclosure(s).
Example: figure 9 shows the Sfc having ten valve
locations per module. this means when the system
pulses, “1” is the first pulse in the sequence, “2” is
the second, “3” is the third, etc.
When multiple dust collector modules are installed,
daisy chain the wiring so that each solenoid valve
with the same module location will pulse at the
same time. this means all #1 solenoid valves are
connected together and wired to pulse control panel
“out 1,” #2 solenoid valves are connected together
and wired to pulse control panel “out 2,” etc. refer
to figure 9 for the Sfc dust collector solenoid valve
wiring information. When cleaning, the pulse valves
sequence left to right, top to bottom.
unless specified on the uaS sales order, the customer
will supply interconnecting material (conduit, wiring,
etc.) from the pulse control panel to the Sfc.
CAUTION
!
D A N G E R