CLARCOR UAS SFC Series, Руководство пользователя

Страница: 11 / 40

6
revised 04/15
Sfc
cartridge Dust collector
3.3.1.1 SINGLE MODULE HOPPER
ASSEMBLY
assemble four leg weldments to hopper (refer to figure
4, Detail a), making sure base pads are oriented as
illustrated. after four legs have been bolted to the
support hopper, locate the four support braces which
measure 60-11/16” between hole centers, and attach to
left and right side of hopper legs as shown in figure 4.
Locate the two support braces, which measure 55-1/16”
between hole centers. these braces are to be attached
to back legs as illustrated in figure 4.
after all support braces have been installed. Bolt brace
together as illustrated in fig. 4, Detail B.
Secure hopper/leg assembly to concrete mounting
pad with appropriate mounting hardware. anchors
should be provided by customer or contractor
according to local codes.
3.3.1.2 MULTIPLE MODULAR HOPPER
ASSEMBLIES
Position multiple hoppers side by side and bolt through
corner gussets as illustrated in figure 5, Detail D. after
hoppers have been securely fastened, refer to figure 6 to
locate your hopper configuration. using this configuration
and figure 5, Detail e, locate and attach the leg
weldments to the hopper assembly. Locate the diagonal
support brace which measures 60-11/16” and attach it to
the hopper corner brackets on left and right side of hopper
referencing figure 5 hopper configuration and figure 6,
making sure the base pads are oriented as illustrated
in figure 6. Locate the support braces, which measure
55-1/16” between hole centers. these braces are to be
attached to the back legs as illustrated in figure 5,
Details a and c.
after all support braces have been installed, bolt side
braces together where they cross as illustrated in
figure 5, Detail B.
Secure hopper/leg assemblies to concrete
mounting pad with appropriate mounting hardware.
anchors should be provided by customer or
contractor according to local codes.
3.3.2 FULLY ASSEMBLED FILTER MODULE
SECTIONS
apply two ribbons of sealant to hopper flange to
create “figure 8” pattern around mounting holes.
refer to figure 7, Detail a.
Place filter module onto hopper/leg assemblies (refer
to figure 7). Drift pins will also be useful for locating
the filter module section onto the hopper.
NOTE: each hopper assembly is equipped with four
1/2” (13mm) pry locations – two holes on front
flange and two holes on rear flange. refer to
figure 7, Detail c, to aid in aligning the hopper
flange with the module flange.
With filter module still supported, use hardware (refer
to figure 7, Detail a) to bolt the hopper and filter
module together. Securely tighten all hardware at the
filter module and hopper. recheck leg assembly sway
braces to ensure they are tight. install fasteners (bolt,
flat washer, lock-washer, nut) to all four pry locations.
Disconnect lifting slings and spreader bars used for
installation.
3.3.3 MULTIPLE, BOLT-TOGETHER MODULE
SECTIONS (APPLIES TO 4 OR MORE
MODULES)
for units that have multiple bolt-together module
sections, remove the row of filters from the modules
nearest the bolting flange (refer to Section 5.1).
Protect the doors and filters removed by placing in a
safe area away from work area. identify the different
module sections. there are left (bolt flange on right
side), right (bolt flange on left side) and possibly
center (bolt flanges on both sides) module sections.
install all hopper/leg assemblies as previously
described in Section 3.3.1.1 and 3.3.1.2.
apply two ribbons of sealant to hoppers that are
located under the dust collector section that is being
installed (refer to figure 7, Detail a).
CRUSH AND ELECTROCUTION HAZARD
in preparing to attach the filter module to the hopper,
connect lifting slings and spreader bars to all filter
module lifting lugs with clevis pins. Distribute the
load evenly. Location must be clear of all
obstructions, such as utility lines or roof overhangs.
Place the appropriate filter module onto hopper/leg
assembly to which the sealant has been applied,
positioning filter module corner holes over alignment
holes (refer to figure 7, Detail c). Drift pins will also
be useful for locating the filter module section onto
the hopper.
NOTE: each hopper assembly is equipped with four
1/2” (13mm) pry locations – two holes on front
flange and two holes on rear flange. refer to
figure 7, Detail c, to aid in aligning the hopper
flange with the module flange.
With filter module still supported, use hardware (refer
to figure 7, Detail a) to bolt the hopper and filter
module together. Securely tighten all hardware at the
filter module and hopper. recheck leg assembly sway
braces to ensure they are tight. install fasteners (bolt,
flat washer, lock-washer, nut) to all four pry locations.
!
D A N G E R
!
WARNING
!
WARNING