background image

24

revised 04/15

Sfc

cartridge Dust collector

4.3.2   DIGITAL PULSE CONTROL (DPC) 

PANEL

the DPc Pulse control Panel is set for “Pressure 

Switch” or “PS” pulse mode. With the DPc control, 

the desired pressure can be maintained by adjusting 

the high and low set-points on the panel. the factory 

setting is 3.0 (high set-point) and 2.5 (low set-point). 

this allows a 0.5” “deadband” and the pulse system will 

maintain the desired pressure. the high and low set-

points on the DPc can be adjusted as the filters season 

and continuous pulsing occurs. adjust upward in 0.5” 

increments until pulsing stops. continue adjustments, 

when required, until the high set-point reaches 5”.  

no further adjustments should be made over 5” w.g.

5.  SERVICE

   Before servicing dust collector:

  •  Wear appropriate protective clothing when servicing 

dust collector.

  • Disconnect and lockout electrical power to the unit 

and control panel.

  • Close off and slowly bleed the compressed air 

 

supply from the air manifold reservoir. air manifold 

reservoir pressure should be reduced to 0 PSiG  

(0 Bar).

  • Collected dust may be hazardous. Consult proper 

authorities for handling and disposal.

  • Collected dust may be a potential fire hazard. 

Welding, grinding or operations involving open 

flames should not be performed without fire 

protection measures in place. refer to Section 1  

of this manual for additional precautions.

  • Disposal of collected dust must be according 

to federal, state and local regulations and all 

appropriate authorities.

5.1  CARTRIDGE FILTER REMOVAL AND 

REPLACEMENT

Protura

®

 nanofiber filters are the only replacement filters 

which provide the highest level of performance expected 

from the Sfc Dust collector.
replacement cartridge filters should be ordered when  

the differential pressure is consistently above 5” w.g. 

(127 mmaq) or system airflow is inadequate and won’t 

significantly recover with off-line (no fan pulse) cleaning.  

to order filters, contact uaS at 888-515-8800.

TO REPLACE CARTRIDGE FILTERS

1.   read and follow caution instructions in box above 

before servicing your unit.  Start with the top row of 

QuickSeal doors. (figure 17)

2.   tap the metal surface of each filter access door to 

remove collected particles from the inner door gasket. 

Pull the QuickSeal door handle away from the dust 

collector until the handle makes a 90° angle with 

the door cover. the filter access door is now in an 

unlatched position. Lift the QuickSeal filter access 

door upward until the door rods clear the side support 

brackets. Pull the door away from the dust collector. 

tilt the door cover away from the dust collector once 

free from the support brackets to trap any dust on the 

inside of the filter access door. Dispose of dust into a 

suitable container. Place filter access door in a  

safe place.

3.   Move filter from side to side to break the gasket seal 

between filter-to-filter-to-tubesheet locations. rotate 

the filter 180° to allow the dust on top of the cartridge 

filter to fall into the dust collector hopper.

4.   Slide the filters out of the dust collector and transfer to 

a suitable disposal container. repeat this procedure 

for the remaining filters.

5.   inspect the tubesheet and make certain the gasket 

sealing area is free of dust to ensure proper sealing 

of the new filter. Make certain the area is dry after the 

cleaning process is complete.

6.   install new Protura

®

 nanofiber cartridges into each 

filter compartment, gasket end first. clean the filter 

door gaskets and align with door rod support brackets 

on the dust collector. Door handle must be placed at 

a 90° angle to filter access door prior to placing the 

door cover plate support rod in the support brackets 

(refer to figure 17). the flat surface of the door 

handle should be facing downward. to close the filter 

access door, push the door handle upward,  

toward the unit.

    the QuickSeal filter access door handle must be  

in a perpendicular orientation to door surface prior to 

being closed. a flat solid section of door handle will be 

visible when door assembly is in the properly closed 

position. refer to figure 17.

    if cam surface of the door handle is visible, QuickSeal 

filter door assembly has been improperly installed.

7.   the Sfc dust collector is now ready to be placed 

back in service. reconnect electrical power and air 

supply. Please follow the initial start-up checklist to 

ensure proper unit performance.

5.2  DUST REMOVAL

    Do not let the dust storage drum overfill. this can 

cause poor dust collector performance and require 

extensive clean-up due to the overflow of dust  

when removing the collection container(s).

!

 

WARNING

!

 

WARNING

 

!

  D A N G E R

Содержание UAS SFC Series









































Отзывы: