Cisco Nexus 92160YC-X Скачать руководство пользователя страница 61

Страница: 61 / 72

DC Power Cable Specifications

Cord Set Description

Power Cord

Power Supply

8 AWG insulated cable (10 AWG
minimum) for each power supply

(customer supplied)

UCSC-PSU-930WDC (port-side
intake airflow)

8-AWG cable with 3-pin keyed
power supply connector and three
wires (power source connection)

CAB-48DC-40A-8AWG

UCS-PSU-6332-DC (port-side
exhaust airflow)

No power cord included with
switch

NO-POWER-CORD

All except Argentina, Brazil, and
Japan

Regulatory Standards Compliance Specifications

The following table lists the regulatory standards compliance for the switch.

Table 1: Regulatory Standards Compliance: Safety and EMC

Description

Specification

Products should comply with CE Markings according to directives 2004/108/EC
and 2006/95/EC.

Regulatory compliance

• UL 60950-1 Second Edition

• CAN/CSA-C22.2 No. 60950-1 Second Edition

• EN 60950-1 Second Edition

• IEC 60950-1 Second Edition

• AS/NZS 60950-1

• GB4943

Safety

Cisco Nexus 9236C NX-OS Mode Switch Hardware Installation Guide

System Specifications

DC Power Cable Specifications

Содержание Nexus 92160YC-X









































































Результаты поиска

Содержание Nexus 92160YC-X

Отзывы:

Похожие инструкции для Nexus 92160YC-X

Бренды по названию

Популярные бренды

Cisco Nexus 92160YC-X, Руководство по установке оборудования

Результаты поиска

Содержание Nexus 92160YC-X

Отзывы:

Похожие инструкции для Nexus 92160YC-X

Бренды по названию

Популярные бренды