Cisco Nexus 92160YC-X Скачать руководство пользователя страница 64

Страница: 64 / 72

Status

Color

LED

Port admin state is 'Enabled', SFP
is present and the interface is
connected (that is, cabled, and the
link is up).

Green

(port)

Port admin state is 'Disabled, or the
SFP is absent, or both.

Amber

Port admin state is 'Enabled' and
SFP is present, but interface is not
connected.

Off

Lane Link LEDs

The Lane Link LEDs indicate which of the break out lanes are being checked. If none of the Lane Link LEDs
is lit, all four lanes are being checked.

Description

LED Lit

Checking lane 1.

Checking lane 2.

Checking lane 3.

Checking lane 4.

Checking all four lanes

None

Fan Module LEDs

The fan module LED is located below the air holes on the front of the module.

Status

Color

LED

The fan module is operational.

Green

STS

The fan module is not operational (fan is probably not functional).

Red

Fan module is not receiving power.

Off

Power Supply LEDs

The power supply LEDs are located on the left front portion of the power supply. Combinations of states

indicated by the Okay (

) and Fault (

) LEDs indicate the status for the module as shown in the following

table.

Cisco Nexus 9236C NX-OS Mode Switch Hardware Installation Guide

LEDs

Lane Link LEDs

Содержание Nexus 92160YC-X









































































Результаты поиска

Содержание Nexus 92160YC-X

Отзывы:

Похожие инструкции для Nexus 92160YC-X

Бренды по названию

Популярные бренды

Cisco Nexus 92160YC-X, Руководство по установке оборудования

Результаты поиска

Содержание Nexus 92160YC-X

Отзывы:

Похожие инструкции для Nexus 92160YC-X

Бренды по названию

Популярные бренды