Cisco Nexus 92160YC-X Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 72

background image

switch and you need to replace it, install the new power supply in the open slot and power it up before
removing the original power supply.

• Ensure that the chassis is grounded. For grounding instructions, see

Grounding the Chassis, on page 24

.

Step 1

Pull the power cord out from the power receptacle on the power supply to be removed and verify that the

LED turns

off.

The

LED might be on and amber colored to indicate that the input power has been disconnected.

Note

If you need to remove an Anderson's Saf-D-Grid power cable connector from a high-voltage power supply,
press the tab at the top of the connector and pull the connector out of the power supply.

Note

Step 2

Remove the power supply from the chassis by pushing and holding its thumb latch to the left and pulling the power supply
part way out of the chassis.

Step 3

Place your other hand under the power supply to support it while you slide it out of the chassis.

Either place the power supply on an antistatic surface or pack it in its packing materials.

Step 4

If the power supply slot is to remain empty, install a blank power supply filler panel (part number N2200-P-BLNK).

What to do next

You are ready to install the replacement power supply.

Removing an HVAC/HVDC Power Supply

You can remove one power supply while the other one provides power to the switch.

To disconnect the power supply from its power cables, you must shut off the power from the power source
and then either disconnect a connector for the power cables or release each of three cables from the power
supply (requires a standard screw driver).

Step 1

Turn off the circuit breaker for the power feed to the power supply that you are replacing.

Be sure that the LEDs turn off on the power supply that you are removing.

Step 2

Remove the power cable from the power supply by pressing the tab on the top of the Anderson Power SAF-D-Grid
connector and pull the cable and connector out of the power supply.

Step 3

Grasp the power supply handle while pressing the release latch towards the power supply handle.

Step 4

Place your other hand under the power supply to support it while you slide it out of the chassis.

Do not touch the electrical connectors on the back side of the module and prevent anything else from coming
into contact with and damaging the connectors.

Caution

Cisco Nexus 9236C NX-OS Mode Switch Hardware Installation Guide

35

Replacing Modules

Removing an HVAC/HVDC Power Supply

«
...
43
44
45
46
47
...
»

Содержание Nexus 92160YC-X









































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 92160YC-X

Бренд: eao Страницы: 2

Бренд: eao Страницы: 2

Бренд: vantiva Страницы: 58

Бренд: GALCO Страницы: 22

Crouse-Hinds CEAG KO

Бренд: Cooper Страницы: 12

Бренд: Linksys Страницы: 3

Бренд: Black Box Страницы: 4

Бренд: Gefen Страницы: 11

ServSwitch KV1510A

Бренд: Black Box Страницы: 16

Бренд: Magnum Страницы: 3

Cyber SWITCH 1000

Бренд: Cabletron Systems Страницы: 106

Бренд: Samson Страницы: 64

S5130S-EI series

Бренд: H3C Страницы: 67

PFS4226-24ET-240

Бренд: Dahua Страницы: 3

Бренд: KYLAND Страницы: 34

Бренд: TRENDnet Страницы: 2

Бренд: Black Box Страницы: 50

SECURVIEW SV-7020

Бренд: CrimeStopper Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды