Cisco Nexus 92160YC-X Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 72

background image

• Green (DC power supplies)

• Port-side exhaust airflow modules

• Blue (fan modules and AC power supplies)

• Gray (DC power supplies)

• Dual-direction airflow power-supply modules

• White (see the color of the fan modules to determine the airflow direction used)

All power supplies and fan modules must have the same direction of airflow.

Note

Installing the Switch using the NXK-ACC-KIT-1RU Rack-mount
Kit

To install the switch, you must attach front and rear mounting brackets to the switch, install slider rails on the
rear of the rack, slide the switch onto the slider rails, and secure the switch to the front of the rack. Typically,
the front of the rack is the side easiest to access for maintenance.

You must supply the eight 10-32 or 12-24 screws required to mount the slider rails and switch to the rack.

Note

Before you begin

• You have inspected the switch shipment to ensure that you have everything ordered.

• Make sure that the switch rack-mount kit includes the following parts:

• Front rack-mount brackets (2)

• Rear rack-mount brackets (2)

• Slider rails (2)

• M4 x 0.7 x 8-mm Phillips countersink screws (12)

• The rack is installed and secured to its location.

Step 1

Install two front rack-mount brackets and the two rear rack-mount brackets to the switch as follows:

a) Determine which end of the chassis is to be located in the cold aisle as follows:

• If the switch has port-side intake modules (fan modules with burgundy coloring), position the switch so that its

ports will be in the cold aisle.

Cisco Nexus 9236C NX-OS Mode Switch Hardware Installation Guide

17

Installing the Switch Chassis

Installing the Switch using the NXK-ACC-KIT-1RU Rack-mount Kit

«
...
25
26
27
28
29
...
»

Содержание Nexus 92160YC-X









































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 92160YC-X

Бренд: Barco Страницы: 6

DynaGST/2402G GEP-33224T-1

Бренд: UNICOM Страницы: 1

Cleveland Controls RSS-498-013

Бренд: UNICONTROL Electronic Страницы: 2

Draco major K474-U8/C8

Бренд: Ihse Страницы: 167

Бренд: steute Страницы: 10

Бренд: XtendLan Страницы: 24

CentreCOM GS970M Series

Бренд: Allied Telesis Страницы: 21

Бренд: Technische Alternative Страницы: 4

CT.TS005.003902

Бренд: Talkswitch Страницы: 309

Бренд: ADC Страницы: 75

USB 2.0 7-Port Hub HO97916

Бренд: GE Страницы: 19

S3100-16T P-EI-W

Бренд: H3C Страницы: 60

Бренд: Gira Страницы: 2

Бренд: Good Way Страницы: 13

Extricom AT-EXLS-3000

Бренд: Allied Telesis Страницы: 120

Бренд: Epcom Страницы: 2

Бренд: Anybus Страницы: 126

Бренд: Comtrend Corporation Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды