Cisco MDS 9148T Скачать руководство пользователя страница 17

Страница: 17 / 70

State

Status

Color

Function

Location

Indicator

All diagnostics have passed,
Cisco NX-OS is running
and the system is
operational.

Solid On

Green

System Status

Front panel of
the chassis

Status LED

Any of the following
conditions exists:

• The system is running

bootup diagnostics.

• The system is booting.

• A minor temperature

threshold is exceeded.

Solid On

Orange

Mismatched airflow
direction observed in one of
the following modules:

• Fan modules—The

switch will go down in
10-15 seconds.

• PSUs—The switch

will go down after 10
minutes.

• Fan modules and

PSUs—The switch
will go down after 10
minutes.

Blinking

Red

One of the following
conditions exists:

• A diagnostic test failed

or another fault
occurred during
bootup.

• A major temperature

threshold is exceeded.

Solid On

All fan modules are
operational.

Solid on

Green

Fan health

Front panel of
the chassis

Fan status

Fan failure.

Solid on

Red

Cisco MDS 9148T 32-Gbps 48-Port Fibre Channel Switch Hardware Installation Guide

Overview of Cisco MDS 9148T Fibre Channel Switch

LEDs

Содержание MDS 9148T







































































Результаты поиска

Содержание MDS 9148T

Отзывы:

Похожие инструкции для MDS 9148T

Бренды по названию

Популярные бренды

Cisco MDS 9148T, Руководство по установке оборудования

Результаты поиска

Содержание MDS 9148T

Отзывы:

Похожие инструкции для MDS 9148T

Бренды по названию

Популярные бренды