Cisco MDS 9148T Скачать руководство пользователя страница 51

Страница: 51 / 70

Installing a Cable into an SFP Transceiver

To prevent possible damage to the cable or transceiver, install the transceiver in the port before installing the
cable in the transceiver.

Caution

To install a cable into a transceiver, follow these steps:

Step 1

Attach an ESD-preventive wrist strap and follow its instructions for use.

Step 2

Remove the dust cover from the connector on the cable.

Step 3

Remove the dust plug from the cable end of the transceiver.

Step 4

Align the cable connector with the transceiver and insert the connector into the transceiver until it clicks into place.

Figure 17: Connecting an LC-Type Cable to a Fibre Channel Port

The LC connector has keys to allow insertion only one way into the transceiver. If the cable does not install
easily, ensure that it is correctly oriented before continuing.

Caution

For instructions on verifying connectivity, see the

Cisco Fabric Manager Fundamentals Configuration Guide

and the

Cisco NX-OS Fundamentals Configuration Guide

Removing a Cable from an SFP Transceiver

• When pulling a cable from a transceiver, grip the body of the connector. Do not pull on the jacket sleeve

because this can compromise the fiber optic termination in the connector.

• If the cable does not remove easily, ensure that any latch present on the cable has been released before

continuing.

Caution

To remove the cable, follow these steps:

Cisco MDS 9148T 32-Gbps 48-Port Fibre Channel Switch Hardware Installation Guide

Connecting the Cisco MDS 9148T Switch

Installing a Cable into an SFP Transceiver

Содержание MDS 9148T







































































Результаты поиска

Содержание MDS 9148T

Отзывы:

Похожие инструкции для MDS 9148T

Бренды по названию

Популярные бренды

Cisco MDS 9148T, Руководство по установке оборудования

Результаты поиска

Содержание MDS 9148T

Отзывы:

Похожие инструкции для MDS 9148T

Бренды по названию

Популярные бренды