Cisco MDS 9148T Скачать руководство пользователя страница 18

Страница: 18 / 70

State

Status

Color

Function

Location

Indicator

No input to the PSU.

Off

Green

PSU input/output

Faceplate of
each PSU

PSU Status
Indicators

PSU output is OK.

Solid on

PSU output is not OK, but
input is OK.

Blinking

PSU is operating normally.

Off

Amber

PSU operation

One of the following
conditions exists in the
PSU:

Over voltage

Over current

Over temperature

Fan failure.

Solid on

PSU has a fault, but is still
operational.

Blinking

Fan module is operating
normally.

Solid on

Green

Fan module

Faceplate of
each fan module

Fan Status

The fan in the fan module
has failed.

Solid on

Amber

The following table describes the Ethernet port LEDs for a Cisco MDS 9148T switch.

State

Status

LED
Position

There is no link.

Off

Left

Indicates a physical
link.

Solid Green

There is no link traffic.

Off

Right

Indicates link traffic.

Blinking
Yellow

The following table describes the Fibre Channel port LEDs for a Cisco MDS 9148T switch.

State

Status

The link is up.

Solid Green

The link is up and the port beacon is active.

Regular Blinking Green

The link is up (and traffic is flowing through the port).

Intermittent Blinking
Green

Cisco MDS 9148T 32-Gbps 48-Port Fibre Channel Switch Hardware Installation Guide

Overview of Cisco MDS 9148T Fibre Channel Switch

LEDs

Содержание MDS 9148T







































































Результаты поиска

Содержание MDS 9148T

Отзывы:

Похожие инструкции для MDS 9148T

Бренды по названию

Популярные бренды

Cisco MDS 9148T, Руководство по установке оборудования

Результаты поиска

Содержание MDS 9148T

Отзывы:

Похожие инструкции для MDS 9148T

Бренды по названию

Популярные бренды