Cisco MDS 9148T Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 70

background image

If you do not order a power cord with the system, you are responsible for selecting the appropriate power cord
for the product. Using a noncompatible power cord with this product may result in electrical safety hazard.
Orders delivered to Argentina, Brazil, and Japan must have the appropriate power cord ordered with the
system.

Caution

Standard Power Cords

Cisco standard power cords for the Cisco MDS 9148T switch have an IEC C15 connector on the outlet end
of the cord and a country specific plug on the inlet end of the cord. To see the list of supported standard power
cords, see the

Cisco MDS 9148T 32-Gbps 48-Port Fibre Channel Switch Data Sheet

.

Jumper Power Cord

Jumper power cords have an IEC C15 connector on the outlet end of the cord and an IEC C14 connector on
the inlet end of the cord. This cord is compatible with IEC C13 outlet receptacles. This type of outlet receptacle
is commonly used for power distribution inside cabinets.

To see the list of supported jumper power cords, see the

Cisco MDS 9148T 32-Gbps 48-Port Fibre Channel

Switch Data Sheet

.

Fibre Cable Specifications

For information on the fibre cable specifications, see the

Cisco MDS 9000 Family Pluggable Transceivers

Data Sheet

.

Cisco MDS 9148T 32-Gbps 48-Port Fibre Channel Switch Hardware Installation Guide

60

Cable and Port Specifications

Standard Power Cords

«
...
64
65
66
67
68
...
»

Содержание MDS 9148T







































































Отзывы:

Нет отзывов

Похожие инструкции для MDS 9148T

D DGS-3048 DGS-3048

Бренд: D-Link Страницы: 3

Бренд: Painless Performance Products Страницы: 2

Бренд: Camozzi Страницы: 2

Бренд: JB Systems Light Страницы: 15

Бренд: HPM Страницы: 4

LambdaUnite MSS

Бренд: Lucent Technologies Страницы: 388

Бренд: Vector Страницы: 6

Бренд: ASTEK Страницы: 3

Бренд: Maiwe Страницы: 5

Бренд: VeEX Страницы: 22

PFS4226-24ET-240

Бренд: Dahua Страницы: 3

Бренд: Manhattan Страницы: 2

Бренд: National Instruments Страницы: 12

Бренд: Comm-Tec Страницы: 10

Бренд: Omron Страницы: 6

Бренд: SMART-AVI Страницы: 9

Бренд: Edimax Страницы: 8

Бренд: Hored Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды