Cisco FM1200 Volo Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 175

background image

Every Cisco unit uses a proprietary distributed-channel switching
algorithm. If the UNII2 plug-in is installed, and a TDWR radar transmission
is detected:

• The algorithm will attempt to switch communicating Cisco units

to the next radar-free channel, allowing uninterrupted
communications with no radar interference.

• The number of detected radars is reported in the command-line

interface (CLI).

The number of TDWR transmissions detected by the unit is shown in the
command-line interface (CLI), and in

“The device status view” (page 134)

.

To enable the use of U-NII-2A, U-NII-2C and U-NII-2E frequency bands on
the unit, do the following steps:

1.

Contact your Cisco Networks representative to obtain the theDFS
plug-in (part number

FM-UNII2

) free of charge.

2.

Install the UNII2 plug-in as shown in

“Plug-in management

procedures” (page 145)

3.

When you activate the UNII2 plug-in through the Cisco
Partner Portal, you will be prompted to point out the exact
location where the unit will be installed.

• The Partner Portal will verify that there are no TDWR radar

installations within 40 miles (64 Km) of the Cisco unit.If no
TDWR radar installations are found, the plug-in willgrant

permission for the unit to be set to frequencies withinthe

5.250 GHz-to-5.350 GHz band, and the 5.470 GHz-
to-5.725 GHz band.

• If the unit is already set to an operating frequency that is

within the above frequency bands, a banner will appear in
the Configurator UI, recommending that you contact
Cisco Support to request the

FM-UNII2

plug-in, and

verify the location of the unit.

IMPORTANT

Cisco  Systems  Inc.  will  not,  under  any
circumstances,  be  held  liable  for  any  incidental,
consequential or special damages, whether based on
tort,  contract,  or  otherwise,  arising  out  of  or  in
connection  with  improper  use  or  operation  of  the
channel width functionality and/or UNII2 functionality.

7.4.3. Antenna-alignment tools and physical statistics

The

ANTENNA ALIGNMENT AND STATS

window contains controls to

monitor current and average radio link status during operation of the unit,
allowing you to easily adjust the alignment of the unit's antennas.

Device configuration using the configurator interface

© 2021 Cisco and/or its affiliates. All rights reserved.

Page 68 of 175

«
...
66
67
68
69
70
...
»

Содержание FM1200 Volo
















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FM1200 Volo

Бренд: Sagem Страницы: 2

Бренд: Icom Страницы: 125

Бренд: Strong Страницы: 25

Skyrider Defiant SX24

Бренд: Hallicrafters Страницы: 9

Бренд: SpeakerCraft Страницы: 36

Бренд: Michell Instruments Страницы: 28

C-Tech HD 6600 SST

Бренд: Clarke-tech Страницы: 32

Бренд: Alinco Страницы: 16

Tourguide Wireless Transmitter SR 2020 D

Бренд: Sennheiser Страницы: 32

Бренд: Radio Corporation Pty Страницы: 75

Бренд: Gear4 Страницы: 104

Бренд: IROX Страницы: 2

Бренд: O-Lynx Страницы: 16

Бренд: Comet Страницы: 18

Бренд: Morer Страницы: 15

Бренд: Marantz Страницы: 91

PowerBox Cockpit

Бренд: PowerBox Systems Страницы: 30

Бренд: Philco Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды