Cisco FM1200 Volo Скачать руководство пользователя страница 121

Страница: 121 / 175

Parameter

Default value

Tagged packet (any VID), to local unit
kernel

If native VLAN = ON: Packet not
passed to kernel

If native VLAN = OFF: Packet passed to
kernel if VID = NVID

Access port rules for outgoing packets with unit in Bridge Mode

(Case and

Action)

Tagged packet with valid VID from
remote peer

Packet passed (tagged)

Tagged packet with null (0) VID from
remote peer

Packet passed (untagged)

Packet from local unit kernel

If native VLAN not equal to MVID:
Packet passed, tagged with MVID

If native VLAN = MVID: Packet passed,
untagged

7.6.11. Miscellaneous settings

IMPORTANT

Support  for  FIPS,  CANBUS,  PROFINET  and  QNET  are  only
available  if  the  corresponding  plug-ins  are  installed.  If  the
corresponding  plug-in  is  not  installed,  the  check-box  for  the
relevant option will not be available.

The following plug-ins are needed to activate these features:

• FIPS:

FM-FIPS

• CANBUS:

FM-CANBUS

• PROFINET:

FM-PROFINET

• QNET:

FM-QNET

Note that FIPS support is not available for the FM1000
Gateway and FM10000 Gateway.

Contact your Cisco Networks representative for details.

The

MISC SETTINGS

window contains controls to change the following

settings:

• The device name, as used to identify the Cisco FM1200 Volo within

the FMQuadro network map and to other Cisco utilities.

• The operation of the physical Reset button on the unit.

• Device firmware upgrades by trivial file transfer protocol (TFTP).

• The unit's federal information processing standards (FIPS) 140-2

compliance settings (if applicable).

• The unit's controller area network (CANBUS) support settings (if

applicable).

Device configuration using the configurator interface

Page 121 of 175

Содержание FM1200 Volo
















































































































































































Результаты поиска

Содержание FM1200 Volo

Отзывы:

Похожие инструкции для FM1200 Volo

Бренды по названию

Популярные бренды

Cisco FM1200 Volo, Руководство по установке и настройке

Результаты поиска

Содержание FM1200 Volo

Отзывы:

Похожие инструкции для FM1200 Volo

Бренды по названию

Популярные бренды