Cisco FM1200 Volo Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 175

background image

Figure 21. Cisco Configurator (landing page)

2.

The lower section of the

RACER™ Configuration Mode

box has

two radio buttons that show whether the unit is in

Online (Cloud-

Managed)

mode, or

Offline

mode.

3.

If the unit is not in the correct mode, click the

Online (Cloud-

Managed)

or

Offline

radio button as needed.

• A confirmation dialog will be shown, asking if you want to

switch the unit to the chosen mode.

To switch the radio to the chosen mode, click the

4.

Confirm

button.

• A ten-second countdown will be shown.
• The Configurator interface web page will reload.
• The unit will be switched to the chosen configuration mode.

Uploading a device configuration file from FM Racer

A FM Racer device configuration template contains a set of pre-
configured parameters that can be customized and applied to a single
Cisco device, or to a group of devices.

Device configuration using the configurator interface

© 2021 Cisco and/or its affiliates. All rights reserved.

Page 57 of 175

«
...
55
56
57
58
59
...
»

Содержание FM1200 Volo
















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FM1200 Volo

Бренд: Labgear Страницы: 14

Бренд: Sagem Страницы: 2

Бренд: YouKits Страницы: 1

Бренд: Cloud Страницы: 5

Multimedia Master Remote

Бренд: Remotec Страницы: 19

FTDX5000 - SOFTWARE UPDATE INFORMATION...

Бренд: Yaesu Страницы: 10

Бренд: M-system Страницы: 3

Бренд: Strong Страницы: 20

Бренд: Vaisala Страницы: 52

Бренд: Vaisala Страницы: 18

Бренд: Silicon Laboratories Страницы: 2

Бренд: Easy wave Страницы: 8

Бренд: STONEX Страницы: 49

Бренд: Grundig Страницы: 30

LuxLink IRGT-1001

Бренд: LITEWAY Страницы: 2

Бренд: Eight Страницы: 59

Бренд: Yaesu Страницы: 68

Бренд: Safeguard Supply Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды