Cisco Catalyst 4500e Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 152

background image

1-16

Catalyst 4500 E-Series Switches Installation Guide

OL-13972-01

Chapter 1 Product Overview

Supervisor Engines

Supervisor Engines

The following supervisor engines are available for the Catalyst 4500 series and Catalyst 4500 E-series
switches:

•

Supervisor Engine II-Plus (WS-X4013+) (

Figure 1-5

)

•

Supervisor Engine II-Plus TS (WS-X4013+TS) (

Figure 1-6

)

•

Supervisor Engine II-Plus 10GE (WS-X4013+10GE) (

Figure 1-7

)

Switching module
support (continued)

•

32-port 10/100-Mbps Fast Ethernet plus 2-port 1000BASE-X Layer 3
Gigabit Ethernet routing module (WS-X4232-L3)

•

32-port 10/100-Mbps Fast Ethernet switching module with modular uplink
support (WS-X4232-RJ-XX)

–

4-port MT-RJ uplink module (WS-U4504-FX-MT) (optional)

•

2-port Gigabit Ethernet switching module (WS-X4302-GB)

•

6-port 1000BASE-X Gigabit Ethernet switching module (WS-X4306-GB)

•

6-port Gigabit Ethernet switching module (WS-X4506-GB-T)

•

18-port Gigabit Ethernet switching module (WS-X4418-GB)

•

24-port 10/100/1000B A SE-T G igabit Ethernet sw itching m odule

(

WS-X4424-GB-RJ45)

•

48-port Gigabit Ethernet 1000 BASE LX (SPF) switching module
(WS-X4448-GB-LX)

•

48-port 10/100/1000B A SE-T G igabit Ethernet sw itching m odule

(

WS-X4448-GB-RJ45)

•

24-port IEEE 802.3af-compliant PoE 10/100/1000BASE-T RJ-45 switching
module (WS-X4524-GB-RJ45V)

•

48-port 10/100/1000B A SE-T G igabit Ethernet sw itching m odule

(

WS-X4548-GB-RJ45)

•

48-port Gigabit Ethernet switching module (WS-X4448-GB-SFP)

•

48-port IEEE 802.3af compliant PoE 10/100/1000BASE-T

G igabit

Ethernet

sw itching m odule (

WS-X4548-GB-RJ45V)

•

6-port 10GbE X2 switching module (WS-X4606-X2-E)

•

48-port 802.3af PoE 10/100/1000 RJ45 switching module
(WS-X4648-RJ45V-E)

•

48-port Premium PoE 10/100/1000 RJ45 switching module
(WS-X4648-RJ45V+E)

1.

You will need to configure the 1400 W DC input current as appropriate for the model of switch. Refer to

Appendix A,

“Specifications.”

2.

1000W AC and 1300W AC power supplies will fit and function; however, power management is cautioned and only some
configurations will have adequate power. Please refer to the Cisco Power Calculator at http://tools.cisco.com/cpc/ before
configuring these power supplies.

Table 1-4

Features of the Catalyst 4510R-E Switch (continued)

Feature

Description

«
...
30
31
32
33
34
...
»

Содержание Catalyst 4500e Series

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 4500e Series

Бренд: D-Link Страницы: 16

Бренд: CADDX Страницы: 6

MAGNUM ALERT-725

Бренд: NAPCO Страницы: 8

MAGNUM ALERT 854 SYSTEM

Бренд: NAPCO Страницы: 14

Бренд: NAPCO Страницы: 2

Бренд: NAPCO Страницы: 4

Бренд: NAPCO Страницы: 28

Бренд: NAPCO Страницы: 16

Бренд: Digisol Страницы: 25

Бренд: FAAST Страницы: 12

Бренд: WavestoreUSA Страницы: 15

Wisenet QNE-8011R

Бренд: Hanwha Techwin Страницы: 15

Бренд: C.P. Electronics Страницы: 14

Бренд: COMPRO Страницы: 74

Бренд: Genie Страницы: 11

Бренд: DMP Electronics Страницы: 2

Бренд: Camlux Страницы: 90

Бренд: Conrad Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды