Cisco Catalyst 4500e Series Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 152

background image

1-22

Catalyst 4500 E-Series Switches Installation Guide

OL-13972-01

Chapter 1 Product Overview

Supervisor Engines

•

RESET Button, page 1-24

•

Compact Flash Slot, page 1-24

LEDs

Table 1-6

describes the supervisor engine LEDs.

Gigabit Ethernet Uplink Ports

The Gigabit Ethernet uplink ports operate in full-duplex mode only. GBICs have SC connectors to
interface with multimode fiber (MMF) and single-mode fiber (SMF) cable. For more information about
GBICs, refer to the

Catalyst 4500 Series Module Installation Guide

. Frequently updated compatibility

information for GBICs, X2s, and SFPs are in documents at:

http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html

When two Supervisor Engine Vs are present in a Catalyst 4507R-E and Catalyst 4510R-E, all four
uplinks are active on both Primary (active) and Secondary (standby) supervisor engines by default, or
two uplinks are active in a non-redundant configuration. This limits access to slot 10 on the Catalyst
4510R to ports 3 and 4 only. You can only use the 2-port Gigabit Ethernet switching module
(WS-X4302-GB) in slot 10 (flex-slot) when a Supervisor Engine V is used.

Table 1-6

Supervisor Engine LEDs

LED

Color/State

Description

STATUS

Indicates the results of a series of self-tests:

Green

All diagnostic tests passed.

Red

A test failed.

Orange

System boot or diagnostic test is in progress, or two power
supplies are installed but only one is turned on.

Off

Module is disabled.

UTILIZATION

Green 1–100%

If the switch is operational, this display indicates the current
traffic load over the backplane (as an approximate percentage).

LINK

Indicates the status of the 10/100BASE-T port,
10/100/1000BASE-T or uplink ports:

Green

The link is operational.

Orange

The link is disabled by user.

Flashing orange

The power-on self-test indicates a faulty port.

Off

No signal is detected or there is a link configuration failure.

ACTIVE

Indicates whether the uplink port is active or not:

(uplink port)

Green

The port is active.

Off

The port is not active.

ACTIVE

The LED to the right of the uplink ports is only used in switches
with two supervisors. The LED lights on the active supervisor.

«
...
36
37
38
39
40
...
»

Содержание Catalyst 4500e Series

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 4500e Series

Бренд: XP Страницы: 9

Бренд: Basalte Страницы: 2

Бренд: Dahua Страницы: 29

Бренд: 2N Telekomunikace Страницы: 12

Бренд: Watts Страницы: 10

Бренд: Huviron Страницы: 56

Бренд: A-MTK Страницы: 17

NX-108E - Security NetworX NX-4 System

Бренд: GE Страницы: 20

Бренд: UTL Страницы: 2

Бренд: United Security Products Страницы: 16

Бренд: HIKVISION Страницы: 12

Бренд: Messoa Страницы: 31

Бренд: Daikin Страницы: 9

Бренд: CALECTRO Страницы: 4

Бренд: Idis Страницы: 20

Бренд: VADDIO Страницы: 6

EN1260EchoStream

Бренд: Inovonics Страницы: 2

Mobile SMS Guard 300

Бренд: Marmitek Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды