Cisco Catalyst 4500e Series Скачать руководство пользователя страница 19

Страница: 19 / 152

1-3

Catalyst 4500 E-Series Switches Installation Guide

OL-13972-01

Chapter 1 Product Overview

Switch Features

Table 1-1

describes the features of the Catalyst 4503-E switch.

Table 1-1

Features of the Catalyst 4503 Switch

Feature

Description

Ethernet speeds

•

Ethernet (10BASE-T) interface to workstations and repeaters

•

Fast Ethernet (100BASE-T) interface to workstations, servers, switches,
and routers

Note

Autonegotiation of link speed on each 10/100 port allows migration to
100BASE-T from a 10BASE-T installed base.

•

Gigabit Ethernet (1000BASE-T and 1000BASE-X) interfaces for
backbone interconnection of high-performance workstations, servers,
switches and routers

•

10-Gigabit Ethernet interfaces for backbone interconnection of
high-performance switches and routers

Standard equipment

•

Three-slot modular chassis with one slot reserved for a supervisor engine
and two slots for switching modules

•

One hot-swappable fan assembly

•

Two power supply bays

Power supplies

•

Supports a 1000 W, 1300 W, 1400 W, 2800 W, or 4200W AC-input power
supply or a 1400 W DC-input single input or triple-input power supply

•

Optional redundant power supply

Supervisor engine
support

•

Supports the WS-X4013+, WS-X4013+TS, WS-X4013+10GE,
WS-X4515, WS-X4516, WS-X4516-10GE, and WS-X45-Sup6-E
supervisor engines

•

Holds the ASIC-based forwarding engine (data path) and

the management

processor and software (control path)

•

Features interface monitoring, environmental status, and SNMP and
console/Telnet interface

Note

Packets are not forwarded while the module is removed; a system
reboot occurs when a supervisor engine is reinserted.

Switching module
support

•

24-port 10/100BASE-TX Fast Ethernet switching module
(WS-X4124-RJ45)

•

24-port 100BASE-FX Fast Ethernet switching module
(WS-X4124-FX-MT)

•

48-port 100BASE-FX Fast Ethernet switching module
(WS-X4148-FX-MT)

•

48-port 100BASE-LX10 Fast Ethernet switching module
(WS-X4148-FE-LX-MT)

•

48-port 10/100-Mbps Fast Ethernet switching module (WS-X4148-RJ)

•

48-port 100BASE-BX10-D Fast Ethernet switching module
(WS-X4148-FE-BD-LC)

•

48-port 10/100-Mbps Fast Ethernet switching module (WS-X4148-RJ21)

Содержание Catalyst 4500e Series

























































































































































Результаты поиска

Содержание Catalyst 4500e Series

Отзывы:

Похожие инструкции для Catalyst 4500e Series

Бренды по названию

Популярные бренды

Cisco Catalyst 4500e Series, Руководство по установке

Результаты поиска

Содержание Catalyst 4500e Series

Отзывы:

Похожие инструкции для Catalyst 4500e Series

Бренды по названию

Популярные бренды