background image

Connect the PoE or DC12V power connector.
PoE (IEEE 802.3af): Connect the RJ-45 connector to a 
PoE compatible network device that supplied power 
through the Ethernet cable.
DC12V: Connect the DC12V power connector to a 
DC12V power.

SAFETY

When installing your Ax40W camera be sure to avoid:

•  excessive heat, such as direct sunlight or heating appliances

•  contaminants such as dust and smoke

•  strong magnetic fields

•  sources of powerful electromagnetic radiation such as radios or TV transmitters

•  moisture and humidity

•  areas with mechanical vibrations

•  fluorescent lamps or objects that reflect light

•  unstable light sources  as this may cause flickering

•  temperatures below -10° Celsius or 14° Fahrenheit and above 40° Celsius or 104° 

Fahrenheit

.

• 

For more details on installation and operation, please refer to the CD 
provided.

Equipment to be used in a Network Environment 0 per IEC TR62101. The camera is to 
be connected only to PoE network that complies with IEEE 802.3af without routing to the 
outside plant.

POWER SUPPLY

Ensure the supplied voltage meets the power consumption requirements of this camera 
before powering the camera on. Incorrect voltage may cause irreparable damage to the 
video camera and will effectively void the camera warranty. PoE power is supported by 
this camera series.

CLEANING

•  For maximum optical clarity, the camera dome or lens must remain clean. Use a soft, 

dry cloth to remove finger prints or dust from the dome cover.

•   Use a blower to remove dust from the lens.

•  Clean the body with a soft, dry cloth. If it is very dirty, use a cloth dampened with a 

small quantity of neutral detergent, then wipe dry.

•   Do not use volatile solvents such as alcohol, benzene, or thinners, as they may dam-

age the surface finishes.

SERVICING

To avoid electrical shock and to preserve the product warranty, DO NOT disasemble the 
camera. Refer servicing to qualified personnel only.

PACKAGE CONTENTS

1.  User Manual CD x1

2.  Guide Pattern sticker x1

3.  2nd video monitor output BNC cable x1 

4.  Hex key x1 

5.  Plastic Anchor x2

6.  Round Head Screw (Tapping Type) x2

7.  Flat Head Screw (Machine Type 30L) x2

8.  Wing (Butterfly) nut x2

9.  Washer x2

10.  Standard RJ45 Connector x2

11.  Desiccant in a package x1

CAMERA PARTS AND DEFINITIONS

Quick Start Guide

Network 1MP Wedge Camera 

Ax40W2/4/8-series

DISASSEMBLING THE CAMERA

Before you mount and adjust the camera, follow these steps to disassemble the 
camera.

1.  Using the hex key provided, 

loosen two screws on the cover.

2.  Remove the dome cover.

i3-TRNG-CAMS-

Ax40W-series-QuickGuide

.indd

Rev. 

141126

1

User Guide

IP Finder

2

FRONT

CABLE

90°

270°

180°

5

4

3

10

6

7

8

9

Camera Dome

Camera Body - Side View

Camera Body - Top View

VIDEO OUT

RESET

DEFAULT

1.  VIDEO OUT: Video output connector.
2.  DEFAULT: Press and hold for 5 seconds 

to return to factory default.

3.  RESET: Press to reboot system.

DC12V

POE/ETHERNET

WARNING! 

DO NOT connect both PoE and 

DC12V power connectors at the same time. 
For DC power supply use, make sure the 
polarity is correct to avoid malfunction and / 
or camera damage.

ATTACHING THE DESICCANT

1.  Take the desiccant out of the package (#11 on the Accessories list)
2.  Peel the protective layer revealing the adhesive surface on the desiccant and 

attach to the inside of the dome cover as shown in the diagram below.

11

Peel the 

protective 

layer on the 

desiccant

Attach 

dessicant to 

the inside 

of the dome 

cover

Отзывы: