manualshive.com logo in svg

Cisco ASR 903, Руководство пользователя, Страница: 92 / 280

Поделиться
Скачать
Cisco ASR 903 Скачать руководство пользователя страница 92

 

10

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter

  Caveats in Cisco IOS XE 3.7S Releases

•

CSCue25349

 

Symptom:

 Tracebacks seen on the router with inject bypass set to OFF.

 

Conditions:

 This issue occurs after shutting down the core facing interface or any OSPF enabled 

interface.

 

Workaround:

 There is no workaround.These traces does not have any functional impact.

•

CSCue51682

 

Symptom:

 The REP protocol flaps, as indicated by the following error messages: 

*Feb 8 06:51:38.857: %REP-4-LINKSTATUS: GigabitEthernet0/0/1 (segment 10) is 

non-operational due to neighbor not responding *Feb 8 06:51:39.096: %REP-4-LINKSTATUS: 

GigabitEthernet0/0/1 (segment 10) is operational

 

Conditions:

 This issue occurs under the following conditions: 

–

The router is sending traffic using the incremental MAC address table Fast LSL is configured 
using a 200ms timer. 

–

The router is configured with more than 2000 MAC addresses.

 

Workaround:

 Remove fast LSL from the REP configuration. 

•

CSCue60699

 

Symptom:

 The router auto-negotiates full duplex with 1000M half/full duplex configuration.

 

Conditions:

 This issue occurs when the router has Copper SFP with auto-negotiate enabled. and 

SFP is configured with 1000M half-duplex mode.

 

Workaround:

 There is no workaround.

•

CSCue61803

 

Symptom:

 The interface modules do not get powered off, when router is reloaded.

Conditions:

 This issue is occasionally seen on reload.

Workaround:

 There is no workaround.

•

CSCue61850

 

Symptom:

 Memory allocation observed fro CFM EVC BD offload cases- scale configurations

 

Conditions:

 This issue occurs with CFM EVC BD, when 256 session of3.3ms interval and 256 

SLM session are configured and a 

shutdown 

command followed by a 

no shutdown

 command is 

issued on the traffic sending interface. 

 

Workaround:

 Configure CFM session between 50-100.

•

CSCue67835

 Symptom:

 OSPF flap with aggressive timers (2 sec hello interval, 6 sec dead interval).

 

Conditions:

 This issue occurs on router Stateful switchover (SSO).

 

Workaround:

 Use the default OSPF hello timers.

•

CSCue75372

 

Symptom:

 Time-hog traceback seen on router reload or IM reload.

 

Conditions:

 This issue occurs on router bootup or IM bootup.

 

Workaround:

 There is no workaround.

Содержание ASR 903

























































































































































































































































































Отзывы:

Нет отзывов