manualshive.com logo in svg

Cisco ASR 903, Руководство пользователя, Страница: 263 / 280

Поделиться
Скачать
Cisco ASR 903 Скачать руководство пользователя страница 263

 

21

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter

  Caveats in Cisco IOS XE 3.10S Releases

Symptom: 

IOMD crash is seen while performing an SSO when card type is not configured for T1E1 

IM. 

Conditions: 

This issue is observed when the TDM card type is not configured before performing an 

SSO.

Workaround: 

Configure the card type for T1E1 IM before preforming an SSO. 

•

CSCuf20151

Symptom: 

The following error message is displayed when you apply a policy map:

QoS: Configuration failed. Can NOT match ACL in an output policy-map

Conditions: 

This issue is observed when you apply a policy map, reload, or reconfigure of the 

policy map.

Workaround: 

There is no workaround. 

•

CSCuf43275

Symptom: 

The router does not detect traffic through GLC-FE-100EX and GLC-FE-100ZX 

transceivers.

Conditions: 

The router does not support traffic through GLC-FE-100EX and GLC-FE-100ZX 

transceivers.

Workaround: 

There is no workaround. 

•

CSCuf43992

Symptom: 

The router crashes if you configure local span.

Conditions: 

This issue is observed when you configure local span on the router. 

Workaround:

 There is no workaround.

•

CSCuf44077

Symptom:

 The 

show interface

 command output shows incorrect speed values after performing an 

SSO.

Conditions:

 This issue is observed when you use a 100M SFP.

Workaround:

 There is no impact on functionality. Reset the hardware module to resolve this issue. 

•

CSCuf57632

Symptoms:

 When you reload the router, the device may not be able to load the startup configuration 

from NVRAM.

Conditions:

 This issue is sometimes observed when you reload the router.

Workaround:

 Reload the router again. 

Содержание ASR 903

























































































































































































































































































Отзывы:

Нет отзывов