Cisco ASR 903 Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 280

Cisco ASR 903 Скачать руководство пользователя страница 148

6

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter

Caveats in Cisco IOS XE 3.8S Releases

route-target export 2:1

route-target import 2:1

no auto-route-target

router bgp 100

bgp graceful-restart

neighbor 209.165.200.224 remote-as 100

neighbor 209.165.200.224 update-source Loopback1

!

address-family l2vpn vpls

neighbor 209.165.200.224 activate

neighbor 209.165.200.224 send-community extended

neighbor 209.165.200.224 suppress-signaling-protocol ldp

exit-address-family

Caveats in Cisco IOS XE 3.8S Releases

Caveats describe unexpected behavior. Severity 1 caveats are the most serious caveats. Severity 2 caveats
are less serious. Severity 3 caveats are moderate caveats and only select severity 3 caveats are included
in this chapter.

This section describes caveats in Cisco IOS XE 3.8S releases. The following information is provided for
each caveat:

•

Symptom—A description of what is observed when the caveat occurs.

•

Conditions—The conditions under which the caveat has been known to occur.

•

Workaround—Solutions, if available, to counteract the caveat.

Note

If you have an account on Cisco.com, you can also use the Bug Toolkit to find select caveats of any
severity. To reach the Bug Toolkit, log in to Cisco.com and go to

http://www.cisco.com/pcgi-bin/Support/Bugtool/launch_bugtool.pl

. (If the defect that you have

requested cannot be displayed, this may be due to one or more of the following reasons: the defect
number does not exist, the defect does not have a customer-visible description yet, or the defect has been
marked Cisco Confidential.)

The

Dictionary of Internetworking Terms and Acronyms

contains definitions of acronyms that are not

defined in this document:

http://docwiki.cisco.com/wiki/Category:Internetworking_Terms_and_Acronyms_(ITA)

The following sections describe the open and resolved caveats in 3.8S Releases:

•

Open Caveats—Cisco IOS XE Release 3.8(2)S, page 7

•

Resolved Caveats—Cisco IOS XE Release 3.8(2)S, page 12

•

Open Caveats—Cisco IOS XE Release 3.8(1)S, page 20

•

Resolved Caveats—Cisco IOS XE Release 3.8(1)S, page 23

•

Open Caveats—Cisco IOS XE Release 3.8(0)S, page 36

•

Resolved Caveats—Cisco IOS XE Release 3.8(0)S, page 43

«
...
146
147
148
149
150
...
»

Содержание ASR 903

























































































































































































































































































Отзывы:

Нет отзывов