manualshive.com logo in svg

Cisco ASR 903, Руководство пользователя, Страница: 104 / 280

Поделиться
Скачать
Cisco ASR 903 Скачать руководство пользователя страница 104

 

22

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-08

Chapter

  Caveats in Cisco IOS XE 3.7S Releases

•

CSCuc43719

Symptoms:

 The router crashes.

Conditions:

 Occurs when you apply a Network Based Application Recognition (NBAR) 

configuration to the router. There is no specific trigger.

Workaround:

 Remove the NBAR configuration, it is not supported.

•

CSCuc55382

Symptoms:

 The 

show inventory

 command displays incorrect serial number for SFPs and XFPs.

Conditions:

 Occurs after you issue repeated stateful switchovers (SSOs).

Workaround:

 There is no workaround.

•

CSCuc59386

Symptoms:

 Continuous IOMD crashes occur on OC-3 IM. Interfaces on OC-3 IM are not 

configurable and the router displays the the following error message:

"stand-by does not support this command"

Conditions:

 Occurs with OC-3 IM in a redundant configuration when an IOMD crash occurs on the 

active RSP and the standby IOMD session handle is not cleared.

Workaround: 

Reload the standby RSP. 

•

CSCuc62784

Symptoms:

 The router displays traceback error messages at niles_if_count_initialize

Conditions: 

Occurs following a reload or stateful switchover (SSO).

Workaround: 

There is no workaround. However, the issue does not have any functionality impact.

•

CSCuc64654

Symptom:

 The router is unable to ping the remote customer edge (CE) router.

Conditions:

 Occurs when the router is acting as a provider edge (PE) device and is connected to the 

remote PE using dual loopback interfaces for peering with iBGP sessions.

Workaround:

 Use a single loopback interface. Use the same loopback interface for IPv4 and 

VPNv4 address families. 

•

CSCuc66393

Symptom:

 The router loses OC-3 interface configurations after an ISSU upgrade.

Conditions:

 Occurs on OC-3 serial and POS interfaces after an ISSU software upgrade.

Workaround:

 There is no workaround.

•

CSCuc68462

Symptom:

 The router drops PTP traffic.

Conditions:

 The issue occurs occasionally when you configure PTP slave clock to receive 

VLAN-tagged traffic.

Workaround:

 There is no workaround.

•

CSCuc85721

Symptom:

 The router crashes.

Conditions:

 Occurs under the following conditions:

–

MR-APS is configured on serial interfaces on the OC-3 interface module

Содержание ASR 903

























































































































































































































































































Отзывы:

Нет отзывов