manualshive.com logo in svg

Cisco 4700 series, Руководство администратора

Cisco 4700 Series - высокопроизводительный сетевой роутер для предприятий. Простое управление с помощью Administration Manual, доступное для скачивания бесплатно на manualshive.com. Этот manual поможет вам настроить и оптимизировать вашу сеть для максимальной производительности и безопасности.

Поделиться
Скачать
background image

   

Chapter 7      Configuring Redundant ACE Appliances

Overview of Redundancy

7-6

Cisco 4700 Series Application Control Engine Appliance Administration Guide

OL-11157-01 

  •

HTTP connection states (Optional)

  •

Sticky table

Note

In a user context, the ACE allows a switchover only of the FT group that belongs 
to that context. In the Admin context, the ACE allows a switchover of all FT 
groups in all configured contexts in the appliance.

To ensure that bridge learning occurs quickly upon a switchover in a Layer 2 
configuration in the case where a VMAC moves to a new location, the new active 
member sends a gratuitous ARP on every interface associated with the active 
context. Also, when there are two VLANs on the same subnet and servers need to 
send packets to clients directly, the servers must know the location of the gateway 
on the client-side VLAN. The active member acts as the bridge for the two 
VLANs. In order to initiate learning of the new location of the gateway, the new 
active member sends an ARP request to the gateway on the client VLAN and 
bridges the ARP response onto the server VLAN.

FT VLAN

Redundancy uses a dedicated FT VLAN between redundant ACEs to transmit 
flow-state information and the redundancy heartbeat. Do not use this dedicated 
VLAN for normal network traffic. You must configure this same VLAN on both 
peer appliances. You also must configure a different IP address within the same 
subnet on each appliance for the FT VLAN. 

The two redundant appliances constantly communicate over the FT VLAN to 
determine the operating status of each appliance. The standby member uses the 
heartbeat packet to monitor the health of the active member. The active member 
uses the heartbeat packet to monitor the health of the standby member. 
Communications over the switchover link include the following data:

  •

Redundancy protocol packets

  •

State information replication data

  •

Configuration synchronization information

  •

Heartbeat packets

Содержание 4700 series



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4700 series

2N OfficeRoute Quick Manual preview
OfficeRoute
Бренд: 2N Страницы: 11
2N stargate How To Set preview
stargate
Бренд: 2N Страницы: 5
2N Telekomunikace EasyGate IP Brief Manual preview
EasyGate IP
Бренд: 2N Telekomunikace Страницы: 24
Ubiquiti ER-4 Quick Start Manuals preview
ER-4
Бренд: Ubiquiti Страницы: 22
Ubiquiti UniFi UAP-AC-LR Quick Start Manual preview
UniFi UAP-AC-LR
Бренд: Ubiquiti Страницы: 28
Queclink GV600 Series Instruction Manual preview
GV600 Series
Бренд: Queclink Страницы: 9
Q-See QC814 Specifications preview
QC814
Бренд: Q-See Страницы: 2
Draytek Vigor 2710e Quick Start Manual preview
Vigor 2710e
Бренд: Draytek Страницы: 8
EMCIS LISN User'S Operating Manual preview
LISN
Бренд: EMCIS Страницы: 14
TwinMOS Octopus G Series User Manual preview
Octopus G Series
Бренд: TwinMOS Страницы: 29
AMX AXB-PSCV Dimensional Drawing preview
AXB-PSCV
Бренд: AMX Страницы: 1
Maipu SM3100-28TC-AC Install Manual preview
SM3100-28TC-AC
Бренд: Maipu Страницы: 19
Supermicro AOC-STG-I2 User Manual preview
AOC-STG-I2
Бренд: Supermicro Страницы: 15
HMS Anybus AWB3000 Startup Manual preview
Anybus AWB3000
Бренд: HMS Страницы: 18
Vivotek SF8174 Quick Installation Manual preview
SF8174
Бренд: Vivotek Страницы: 13
Riverbed Cascade Express Installation Manual preview
Cascade Express
Бренд: Riverbed Страницы: 92
Tachosys digiDL-B Administration Manual preview
digiDL-B
Бренд: Tachosys Страницы: 15
C&H Technologies AM105 Brochure preview
AM105
Бренд: C&H Technologies Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды