Section 3: Operation
020-100001-01 Rev. 01 (04/07)
3-25
.
Use options in the
Image Settings
menu to alter your main image
without affecting its size or
position. Changes made to the
Image Settings
menu are applied
immediately and are saved when
you exit the menu (press
Exit
or
Menu
). Options not available for
the projector model or source are
disabled and appear dim (gray).
Contrast
(
SHORT CUT:
Press
Contrast
and adjust the slide bar.)
“Contrast” increases or decreases the perceived difference between light and dark
areas of your image (0-100). For best results, keep close to 50. If contrast is set too
high, the light parts of the image lose detail and clarity. If the contrast is set too low,
the light areas will not be as bright as they could be and the overall image will be dim.
For best results, start with a low value and increase so that whites remain bright but
are not distorted or tinted, and that light areas do not become white (i.e., are
“crushed”).
NOTE:
If the environment lighting changes, an adjustment of Gamma is
recommended (see below).
Brightness
(
SHORT CUT:
Press
Bright
an
d adjust the slide bar.)
“Brightness” increases or decreases the amount of black in the image (0-100). For best
results, keep close to 50. Start with a high value and decrease so that dark areas do not
become black (i.e., are “crushed”). Conversely, high brightness changes black to dark
gray, causing washed-out images.
Gamma
(
SHORT CUT:
Press
Gamma
and adjust the slide bar.)
“Gamma” is a global setting that determines what gray shades are displayed between
minimum input (black) and maximum input (white) for all signals. A good gamma
setting helps to optimize blacks and whites while ensuring smooth transitions for the
“in-between” values utilized in other
colors. Thus, unlike “Brightness” and
“Contrast” controls, the overall tone of
your images can be lightened or darkened
without changing the extremes, and all
images will be more vibrant while still
showing good detail in dark areas.
Gamma is used to fine-tune the gamma table currently in use, ranging from 1 – 3 (2.2
= default). If excess ambient light washes out the image and it becomes difficult or
impossible to see details in dark areas, lower the gamma setting to compensate. This
will improve contrast while maintaining good details for blacks. Conversely, if the
image is washed out and unnatural, with excessive detail in black areas, increase the
Image Settings Menu
f
Содержание DW6Kc
