Chima STES2026+ Скачать руководство пользователя страница 12

Страница: 12 / 91

S Layer 2 Managed Switch User Manual

陈泽科技有限公司

www.stephen-tele.com

Disable, port cannot attend . More details, please refer to this chapter introduction to STP protocol.

Flow control

Flow control means switch control speed of receiver and sender . When receiver received ability is lower than sender sent

ability , flow control lose no data.Flow control have two type: one is half-duplex, another is full-duplex. half-duplex flow

control meet Backpressure standard.full-Duplex flow control based on PAUSE frame flow control ,meet IEEE802.3x standard.

In half-duplex mode,receiver source is not enough ,they will start flow control,send a group carrier wave pluse train (artificial

collision signal ), sender detect network carrier wave which is different with their own sent signal, they will pause for a short

time ,then send data. Receiver can deal with data in this time and control flow. This is Backpressure standard.

In full-duplex mode,receiver source is not enough, receiver send a pause frame to sender that they will stop sending data for

a short time . This is IEEE802.3x standard .

Open port flow control,speed of data flow which flow in or from this port is over this port largest speed.half-duplex choose

backpressure, sender speed down by PAUSE frame,Close port flow control, switch discard package which linear velocity is

over this port.

Negotiation method:

100Mbps Switch , 100Mbps port have 5 work mode , 1000Mbps has 6 work mode as following

Auto: Auto-negotiation

10Mbps

／

HD:10M Full Duplex mode

10Mbps

／

FD: 10M Full Duplex mode

100Mbps

／

HD: 100M half-duplex mode

100Mbps

／

FD: 100M Full Duplex mode

1000Mbps

／

FD: 1000M Full Duplex mode

Front number is transfer speed,back number is Duplex mode.Half Duplex mode is both transfer side sending and receiving

file.But at the same time ,only one equipment use network transfer medium . Full Duplex is both transfer side sending or

receiving at the same time. Normal 10Base-T

／

100Base-TX port have the front 5 work mode.For

S, S

offers 1000Mbps shared port. When it works in copper port mode ,the 6 mode above all can work . When it work in optical

mode,

1000Mbps port can only be used in 1000Mbps/FD work mode.

Untag data frame control : when switch work in

802.1Q vlan mode,when the switch port received the frame without 802.1Q

VLAN TAG. At this time, switch can choose transmit data frame normally or throw it away through Untag data frame control .

Port default

VLAN ID:

PVID is short for port default

VLAN ID.If you open

802.1Q VLAN mode and data frame received from

port have no 802.1Q VLAN TAG,switch will put PVID in data frame,and search VLAN group , transmit it and control it

according to PVID data. More details ,please refer to 802.1Q VLAN in this chapter. (Note: Switch cannot modify PVID data

when work in

PORT VLAN or PROTECTED VLAN mode)

4.2.2 Port mirroring

Port mirroring is one or more port ingress ,egress, ingress and egress monitored by one port.

Based on above monitor

configuration ,you can choose ingress egress monitored type: all ,destination MAC address, source MAC address (SA).If you

choose ingress and destination MAC address (DA) monitored ,they only monitor passed package setted by MAC address.

Monitor interval ranges from 0 to 1023. When monitor interval set at 1023, package passed monitor port and meet monitor

require will be copy and send to monitor port at an interval of 1023.When you set at 0,there is no interval and it’s monitored

100%

Содержание STES2026+




























































































Результаты поиска

Содержание STES2026+

Отзывы:

Похожие инструкции для STES2026+

Бренды по названию

Популярные бренды

Chima STES2026+, Руководство пользователя

Результаты поиска

Содержание STES2026+

Отзывы:

Похожие инструкции для STES2026+

Бренды по названию

Популярные бренды