Chima STES2026+ Скачать руководство пользователя страница 37

Страница: 37 / 91

S Layer 2 Managed Switch User Manual

陈泽科技有限公司

www.stephen-tele.com

Figure 5-12 File transferring

TFTP server IP: TFTP server IP address when you utilize TFTP protocol to update or download files.

File name: Transferring file name. Name rule should follow DOS 8+3 file format.

Transferring options:

Upgrade: upgrade the switch.

Backup: Backup the configuration of switch.

5.3.1.5 Save and reset

Configurations show as figure below:

Figure 5-13 Reset

There will be a prompt window after you click the buttons. For example if you click “restore to factory setting”, the

conformation prompt window will show as the figure below:

Figure 5-14 Confirmation prompt window

Click “Ok” to execute some operation or click “cancel” to give up.

Notice:

When the switch is recovered to factory setting, switch’s IP address parameters and administration password will be

configured as factory setting. IP address of factory setting is 192.168.1.254/255.255.255.0. Switch’s user name and password

is “admin”.

Содержание STES2026+




























































































Результаты поиска

Содержание STES2026+

Отзывы:

Похожие инструкции для STES2026+

Бренды по названию

Популярные бренды

Chima STES2026+, Руководство пользователя

Результаты поиска

Содержание STES2026+

Отзывы:

Похожие инструкции для STES2026+

Бренды по названию

Популярные бренды