CHIEF 361043 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 128

CHIEF 361043 Скачать руководство пользователя страница 91

STANDARD LADDER ASSEMBLY INSTRUCTION MANUAL

Chief industries, Inc.

Manual P/N 361043

91

(Alignment Diagram for First Adjustable Platform Half Cage Hoop)

Fasten the other end of the Adjustable Platform Half Cage Hoop to the Eave Platform Adjustable Cage
Post at the corresponding location through the top large elongated slot on the outer face. The TOP
edge of the Adjustable Platform Half Cage Hoop should be parallel to the Adjustable Platform Tread
Sheet.

Continue with the installation of the second and third Adjustable Platform Cage Half Hoops in the
same manner as the first. It is important that each Half Cage Hoop is installed using the same holes on
the aft end of the Half Hoops so additional parts installed later in the assembly will properly line up.

(Assembly Diagram for Second and Third Adjustable Platform Half Cage Hoops)

The Commercial Eave Platform Adjustable Cage package will include (5) five Adjustable Platform 86”
Cage Straps that will attach to the Adjustable Platform Half Cage Hoops through the stand alone holes
around and near the “rounded portion” of the Half Hoops. Insert the 5/16” fasteners in such a way
that the bolt head is INSIDE of the cage assembly with the nuts on the OUTSIDE.

«
...
89
90
91
92
93
...
»

Содержание 361043

































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды