CHIEF 361043 Скачать руководство пользователя | Manualshive

Страница: 87 / 128

background image

STANDARD LADDER ASSEMBLY INSTRUCTION MANUAL

Chief industries, Inc.

Manual P/N 361043

87

Square the Adjustable Platform Tread Sheet Supports to the Adjustable Platform Sidewall Support
Brackets and then attach the Adjustable Platform Angle Kicker Supports using 5/16” Bin Bolts and
5/16” Whiz Nuts so that one end of the Angle Kicker Support is fastened to the Tread Sheet Support
and the other end is attached to the Sidewall Support Bracket.

(Height Positioning for Adjustable Platform Supporting Components)

Important Note:

The Adjustable Commercial Eave Platform Assembly is interchangeable and can be

installed either on the right hand or left hand side of the Ladder Package simply by flipping the
orientation of the Adjustable Platform Tread Sheet and assembling the Platform Handrails, Platform
Handrail Posts and Adjustable Platform Post Supports accordingly.

Now construct the Adjustable Commercial Platform Assembly using 5/16” Bin Bolts and Whiz Nuts,
separate from the Grain Storage Assembly. Once the Adjustable Platform Assembly is together, lift
the platform into place aligning the smaller slotted holes in the Tread Sheet to the holes in the Tread
Sheet Supports and connect them with 5/16” fasteners.

«
...
85
86
87
88
89
...
»

Содержание 361043

































































































































Отзывы:

Нет отзывов

Похожие инструкции для 361043

Бренд: Boss Страницы: 16

Бренд: Boss Страницы: 28

Бренд: Telesteps Страницы: 31

UNIVERSALE EN131 Series

Бренд: S.T.P Страницы: 12

Бренд: sellwood Страницы: 2

Бренд: Vestil Страницы: 5

Бренд: Vestil Страницы: 13

Бренд: Vestil Страницы: 20

Бренд: technocraft professional Страницы: 40

SmartRack SRCABLELADDER18

Бренд: Tripp Lite Страницы: 32

Бренд: Costway Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды