manualshive.com logo in svg

Chattanooga Group INTELECT LEGEND Series, Руководство по обслуживанию

Поделиться
Скачать
Chattanooga Group INTELECT LEGEND Series Скачать руководство пользователя страница 38

CHATTANOOGA 

GROUP INC.  

 

10.  Push the START button. The unit will hold the settings in memory. The display will 
change to CAL2.  

11.  If you are satisfied with the calibration, push START. 

12.  The unit will beep to indicate that the new calibration values have been stored in the 
applicator. 

13.  The display will change to CAL0 and is now ready for the next calibration. 

14.  After both frequencies have been calibrated and before removing the applicator 
head from the power meter, check the accuracy of the power calibration.  Cycle the 
power to the unit off and then back on.  Select continuous duty cycle and increase the 
output to the settings listed. Verify that the power indicated on the UPM-DT-10 power 
meter is within the indicated range.  Check power at both 1 MHz and 3.3 Mhz. 
 

Head size 

Power level 

Output range 

2 cm

2

2 watts 

1.72-2.28 

 4 

watts 3.44-4.56 

5 cm

2

5 watts 

4.3-5.7 

 10 

watts 

8.6-11.4 

10 cm

2

5 watts 

4.3-5.7 

 10 

watts 

8.6-11.4 

 15 

watts 

12.9-17.1 

 20 

watts 

17.2-22.8 

15.  Calibration complete.  If you are not satisfied with the calibration and wish to start 
over, turn the machine OFF and begin at step one listed above. 

 

.

Innovation starts here

 

TM

 

38

 

Intelect

®

 Legend Series Service Manual

 

Содержание INTELECT LEGEND Series











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды