manualshive.com logo in svg

Chattanooga Group INTELECT LEGEND Series, Руководство по обслуживанию

Поделиться
Скачать
Chattanooga Group INTELECT LEGEND Series Скачать руководство пользователя страница 27

CHATTANOOGA 

GROUP INC.  

 

No Ultrasound Output 

 
First, check that the duty cycle or intensity is not so low that you can’t observe 
water movement on the applicator head.  If there is some movement, but not as 
high as expected, use an ultrasound power meter to test the output.  If it is low, 
then follow the Applicator Calibration Procedure in this manual. 
 
If there is absolutely no output, try another applicator.  Any Chattanooga Group 
applicator from an Intelect

®

 Legend or CPS unit that has the same connector will 

work. 
 
Did swapping the applicator fix the problem? 

Yes

 - The applicator is bad. 

No

 - The generator board is probably bad.  Also check the connector and 

harness inside the unit. 

 
If you do not have another applicator, you can check for output on the Ultrasound 
Generator Board using an oscilloscope. Refer to the Ultrasound Generator Board 
drawing and signal list in this manual.  If there is output at the board connector, 
the applicator is bad. 
 

No Stim Output 

 
Does the display change when a treatment is selected? 

No

 - The Stim Board is probably bad.  Also check the connector and 

harness inside the unit. 

Yes

 - First be sure the leads and electrodes are good.  If possible test the 

output with a resistor. 

Next be sure the output type is available at the channel you are 
monitoring.  For example, HiVolt is only available from channel 2.  See the 
manual. 

Also check the output harnesses and connectors or monitor the output at 
the connector on the Stim Board. 

If  these checks do not reveal the source of the problem and there is no 
output in one or more treatment modes, the Stim Board is faulty. 

Innovation starts here

 

TM

 

27

 

Intelect

®

 Legend Series Service Manual

 

Содержание INTELECT LEGEND Series











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды