manualshive.com logo in svg

Chattanooga Group INTELECT LEGEND Series, Руководство по обслуживанию

Поделиться
Скачать
Chattanooga Group INTELECT LEGEND Series Скачать руководство пользователя страница 35

CHATTANOOGA 

GROUP INC.  

 

2.  

Premod

:  With the oscilloscope probe on channel 2, press Channel 2 

button. Press Premod and observe:  Channel 2  Premod.  Adjust output 
with Intensity arrow to 50ma and press Start. Main screen should display  
Channel 2  Premod  with timer counting down from 15:00 and 50ma as 
output with Ch1 - Avail  below.  Verify waveform is similar to that below 
using the oscilloscope. Press Stop to reset. 

 

Premod Waveform; ‘scope set to 10V/div, 1mSec/div 

3.  

HiVolt

:  Press HiVolt and Main Menu should display at top:  Ch2:     High  

Volt. Time should be set to 20:00 and Int should now read 0v.  Press Enter 
to select Probe. Output must display 0v. Press Enter again to select Pads. 
Increase Output with the Intensity up button to 500. Press Start and verify 
that the output waveform is similar to that shown below. Press Enter and 
use Main Menu down button to move to Polarity. Toggle polarity from 
positive to negative and observe that the waveform changes as shown 
below.  Press Stop upon successful completion. 

 

Positive 

Negative 

Hi-Volt Waveforms; ‘scope set to 50V/div, 20uSec/div 

4.  

Russian

:  Press Channel 1 button.  Press Russian & observe:  Channel 1  

Russian .  At Mode, press Enter and select CoContract and press Enter 
again. Main Menu heading must say:  Ch1-2:    Russian. Move down to 
Cycle Time with the arrow keys and press Enter. Select Continuous and 
press Enter again. Increase Intensity with the arrow key to maximum  
100ma  and press Start. Verify on Main screen that both Channels reach 
100 by pressing the Channel 1 and 2 button. Verify that the output 

Innovation starts here

 

TM

 

35

 

Intelect

®

 Legend Series Service Manual

 

Содержание INTELECT LEGEND Series











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды