manualshive.com logo in svg

Chattanooga Group INTELECT LEGEND Series, Руководство по обслуживанию

Поделиться
Скачать
Chattanooga Group INTELECT LEGEND Series Скачать руководство пользователя страница 24

CHATTANOOGA 

GROUP INC.  

 

Intelect Legend Stim Error Messages Explained 

Below is a list of the messages displayed on the LCD screen when an 

error is detected, as well as a brief explanation of the source of the message. 
 

 “Channels Needed for This Mode are Busy” 

Either no channels are open to run a new signal, or the dedicated 
channel for HiVolt is already being used. 

“Over Current Fault on Channels X-X” 

Where X is a channel number.  Indicates that a severe overcurrent 
was detected on the specified channel(s). 

 

Intelect Legend US Error Messages Explained 

Below is a list of the codes displayed on the LEDs when an error is 

detected. 

HHH 

The applicator has reached a temperature that is too high, and the 
US output has been stopped. 

noHd 

No ultrasound applicator detected. 

E03 

An attempt to set up an address on the onewire device failed. 

E04 

An attempt to read data from the ultrasound applicator failed. 

E05 

An attempt to program the ultrasound applicator failed.  This only 
occurs during calibration. 

E06 

The ultrasound applicator memory is full.  This only occurs during 
calibration. 

E07 

The memory device in the ultrasound applicator is not the proper 
type. 

E08 

The ultrasound applicator is uncalibrated. 

 

Innovation starts here

 

TM

 

24

 

Intelect

®

 Legend Series Service Manual

 

Содержание INTELECT LEGEND Series











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды