background image

Advanced Setup

 

 

NTMS6900 / ATXW-5520 Technical Reference 

 

 

Chassis Plans 

 

5-14 

 

 

Available options are:  

 

Not Installed  

Auto  

CD/DVD  

ARMD  

 

If 

Not Installed 

is selected, the other options on the bottom portion of this screen do not display. 

 

 

LBA/Large Mode  

 

This option allows you to enable IDE LBA (Logical Block Addressing) Mode for the specified 

IDE drive. Data is accessed by block addresses rather than by the traditional cylinder-head-sector 

format. This allows you to use drives larger than 528MB.  

 

The Setup screen displays the system option:  

 

LBA/Large Mode [Auto]  

 

Two options are available:  

 

 

Select 

Disabled 

to have AMIBIOS use the physical parameters of the hard disk and do 

no translation to logical parameters. The operating system which uses the parameter table 

will then see only 528MB of hard disk space even if the drive contains more than 

528MB.  

 

Select 

Auto 

to enable LBA mode and translate the physical parameters of the drive to 

logical parameters. LBA Mode must be supported by the drive and the drive must have 

been formatted with LBA Mode enabled. 

 

 

Block (Multi-Sector Transfer) Mode  

 

This option supports transfer of multiple sectors to and from the specified IDE drive. Block mode 

boosts IDE drive performance by increasing the amount of data transferred during an interrupt.  

 

If 

Block Mode 

is set to 

Disabled

, data transfers to and from the device occur one sector at a time.  

 

The Setup screen displays the system option:  

 

Block (Multi-Sector Transfer) [Auto]  

 

Available options are:  

Disabled  

Auto 

Содержание ATXN-5520

























































































































































Отзывы: