Chassis Plans ATXN-5520 Скачать руководство пользователя страница 23

Страница: 23 / 152

ATXN-5520 / ATXW-5520 Technical Reference

Specifications

1-13

Chassis Plans

Mechanical

The Extended ATX form factor of the motherboard complies with the SSI-EEB 2008 – Rev. 1.0 industry

standard for overall board dimensions [12.0” (30.5cm) x 13.0” (33.1cm)] and mounting-hole placements.

The motherboard‟s standard height cooling solution is designed for 2U and greater chassis heights.

UL Recognition

This motherboard is designed to meet UL60950 and CAN/CSA C22.22 No. 60950-00.

Configuration Jumpers

The setup of the configuration jumpers on the motherboard is described below. An asterisk (*) indicates the

default value of each jumper.

NOTE:

For the three-position jumper, "TOP" is toward the bracket end of the board; "BOTTOM" is toward

the Post Code LEDs.

JU8

Password Clear

(two position jumper)

Install for one power-up cycle to reset the password to the default (null password).

Remove for normal operation. *

JU12

CMOS Clear

(three position jumper)

Install on the TOP to clear.

Install on the BOTTOM to operate. *

NOTE:

To clear the CMOS, power down the system and install the jumper on the TOP. Wait for at least two

seconds, move the jumper back to the BOTTOM and turn the power on. When AMIBIOS displays the "CMOS

Settings Wrong" message, press F1 to go into the BIOS Setup Utility, where you may reenter your desired

BIOS settings, load optimal defaults or load failsafe defaults.

W2,

CPU Fan Speed Control

(two position jumper)

Install to run CPU fan at full speed*

Remove to enable ACPI soft control of the CPU cooling fan

Note

: W2 jumper is connected to CPU1 fan header P28 and W4 is for CPU2 fan header P31

W3,

W5,

W6,

System Fan Speed Control

(two position jumper)

nstall to run SYSTEM fan at full speed*

Remove to enable ACPI soft control of the system cooling fan

Note:

The following jumpers provide the speed control capability to the system fan headers listed below;

W3 – P30, W5 – P27, W6 – P26 and W7 – P25.

PSON Soft Control

(two position jumper)

Install to enable ACPI soft control of the PSON signal line*

Remove to disable PSON control

Содержание ATXN-5520

























































































































































Результаты поиска

Содержание ATXN-5520

Отзывы:

Бренды по названию

Популярные бренды

Chassis Plans ATXN-5520, Техническое описание

Результаты поиска

Содержание ATXN-5520

Отзывы:

Бренды по названию

Популярные бренды