CHART MVE Fusion Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 51

CHART MVE Fusion Скачать руководство пользователя страница 9

20994124 REV A



9

3.2 Liquefier

The Liquefier contains the cryocooler and other support / interface control systems
required to operate the MVE Fusion Freezer. Replacement of the liquefier should only be
performed by a representative from Chart Inc. or trained authorized personnel.

The Liquefier consists of the following major components and features:



Cryocooler –

This is the heart of the system that maintains the liquid nitrogen

stored within the systems pressure vessel. See page 12 for more details pertaining

to the Fusions cryocooler.



Graphical User Interface (GUI) –

This is a touch-screen interface with customized

software intuitively designed for monitoring the MVE Freezer. The 155mm x 87mm

backlit LED display provides system security through password protected

admission. The main screen allows quick access to and displays key parameters

such as the internal freezer temperature, the cryogen liquid level, cryocooler motor

temperatures, the cryogen pressure and system alarms.



Battery Backup –

A 12V, 9.0Ah, sealed lead acid battery allows for monitoring of

the freezer parameters and alarms for a minimum of 24 hours after a power loss.



Main Control Board –

An advanced printed circuited board (PCB) with control

logic and memory for storage of settings, parameters and historical events.



Variable Frequency Drive (VFD) –

The cryocooler is powered by this variable

frequency, variable voltage power supply. Control of the VFD is accomplished by

signals sent from the main PCB based on the freezer status. Voltage to the

cryocooler is modulated to maintain a constant freezer temperature and optimize

power consumption.

«
...
7
8
9
10
11
...
»

Содержание MVE Fusion




















































Отзывы:

Нет отзывов