CHART MVE Fusion Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 51

CHART MVE Fusion Скачать руководство пользователя страница 30

20994124 REV A



30

5.2 Operating the Android User Interface

5.2.1 Navigating the GUI

There are several screens available within the fusion android application to monitor the

system performance and doing specialized tasks such as resetting alarms or changing

the system password. To reach other screens within the app, swipe sideways with a

finger, or touch the tabs in the upper left-or right-hand corners of the screen the user is

in. For instance, to reach the “Levels” screen from the “Main” screen, touch the “Level”

heading on the upper right-hand corner, or swipe a finger from the right to left (as if

dragging the screen sideways). Then the “Main” screen will be replaced by the Level”

screen.

5.2.2 Main Screen

The main screen displays several key parameters including Freezer temperature,

cryogen level, and temperature distribution (see

Figure 21

). Some parameters can be

changed from the screen(s); any change takes a minute to become effective, as this is

the sampling interval of the control loop.

«
...
28
29
30
31
32
...
»

Содержание MVE Fusion




















































Отзывы:

Нет отзывов