en 6
15
17
18
19
16
Hang opener
Attaching door arm on the trolley
Electrical connection
Install illuminated push button or
Multi-function door control
(optional accessory)
Mounting door bracket
Fully open the door, put down door opener on the door (Fig� A)�
Lay a piece of wood / cardboard on the marked spot (X)�
The opener must be securely fastened to a structural support of the
garage�
Three representative installations are shown (Fig� B)� Yours may be
different. Hanging brackets (11) should be angled to provide
rigid support. On finished ceilings, attach support bracket(not delivered)
to a self-supporting structio-nal element before installing the opener� For
concrete ceiling mount, use concrete anchors (21) provided�
On each side of opener measure the distance from the opener to the
structural support (or ceiling)� Cut both pieces of the hanging bracket to
required lengths. Flatten one end of each bracket and bend or twist to fit
the fastening angles� Do not bend at the bracket holes� Drill 4,5mm pilot
holes in the structural supports (or ceiling)� Attach brackets to supports
with wood screws (19)�
Lift opener and fasten to hanging brackets with screw (15) and nut (16)�
Check to make sure rail is centered over the door�
Remove piece of wood / cardboard� Operate door manually�
If door hits the rail, raise header bracket�
After the installation of the garage door drive, particularly using a rail
extension, if the rail is observed to be bent up or down for more than 5
cm during the beginning or end of the travel as well as while encounte-
ring an obstacle, a central suspension must be provided by the custo-
mer� For this, please contact the manufacturer of the garage door drive�
NOTE
: The attachment point on the door must be the frame or a stable
place on the door panel� If necessary, drill through and screw (not inclu-
ded) together as shown in Fig� B�
Mount the release handle of the emergency release at a
height less than1�80 m� Attach the yellow label regarding the
release of the garage door opener (sticker) on the cord of the
door handle�
The straight door arm is already pre-assembled.
Recommended installation:
The trolley can be separated from the drive by pulling the red handle
and manually pushing towards the door� When the door is closed,
fix the curved door arm (9) on the door bracket with the bolt (17) and
secure with cotter pin (18)� Connect straight and curved door arms
together flush with an overlap of 2 holes with screw (15) and secure
with nut (16)� Choose the holes in such a way that the door arm
stands at an angle of about 30-40°�
NOTE:
The curved door arm can be omitted, if the door fitting has been
attached at the far upper edge of the door�
Locate door control where the garage door is visible, away from door
and door hardware and out of the reach of children� Mount at least 1,5
m (5 feet) above the floor. Permanently fasten the caution label perman
-
ently to the wall near the door control as a reminder of safe operating
procedures� There are 2 terminals on the back of the door control�
Strip about 6mm of insulation from bell wire� Separate wires enough to
connect the white/red wire to RED terminal screw and the white wire to
WHT terminal screw� Fasten the door control to an inside garage wall
with sheet metal screws provided� Drill 4mm holes and use anchors if
installing into drywall� A convenient place is beside the service door and
out of reach of children� Run the bell wire up the wall and across the
ceiling to the garage door opener� Use insulated staples to secure wire�
Operation of the Door Control:
Press to open or close the door� Press again to stop the door while
moving�
Pay attention to a horizontal course of the rail along the
ceiling�The distance can be adjusted by the given hole spa-
cing. Protruding ends of the ceiling fixture can be reduced if
necessary�
In order to avoid personal injury and damage to the device,
the door opener should be operated only if such an inst-
ruction is explicitly stated in this manual� The power plug
must always be accessible for the purpose of disconnecting the mains
supply� Electrical installations may only be undertaken by an authorized
electrician�
Installation in sectional or one-piece doors:
The door bracket (7) has multiple mounting holes� Attach door bracket
top centre on the inside of the door as shown� Mark holes and screw
door bracket�
1� One-piece or sectional door with a guide rail:
distance to door top edge 0-100 mm�
2� Sectional door with two guide rails:
distance to door top edge 100-130 mm�
