Cetetherm PRESSOSMART MP195NL Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 45

Cetetherm PRESSOSMART MP195NL Скачать руководство пользователя страница 7

7

Pressure

Ph

High alarm Hst+14

Open

Pressure relief

Valve(s)

Closed Hst+9

Neutral Zone

P1 Stop                               Hst+7
                                     E

P2 Stop

d

d

P1 ON
                                     E
P2 ON                                 Hst+1

Hst

Pb

Low P alarm Hst-2

SCHEMATIC DIAGRAM MP4N CLOSED TANK

Arrêt P1

SCHEMATIC DIAGRAM MP5N/MP7 CLOSED TANK

On these units, there may be 1 or 2 pressure control valves.

Same principle than open tank system except that the water level is calculated from the water weight inside
the tank. For this, a weight sensor is connected to an electronic card inside the control box. This card power
supplies the weight sensor and acquires its signal, translated into inner water level, replacing the standard
water level sensors.

Pressure

Ph High P alarm Hst+14

Open

                 Pressure Relief
                        Valve

Closed                                Hst+9

                     Neutral zone

P1 Stop                              Hst+7

                    Start Pump
              d

P0                                       Hst+2
Hst
Pb            Low P alarm        Hst-2

«
...
5
6
7
8
9
...
»

Содержание PRESSOSMART MP195NL














































Отзывы:

Нет отзывов