manualshive.com logo in svg

Cetetherm PRESSOSMART MP195NL, Руководство пользователя, Страница: 23 / 45

Поделиться
Скачать
Cetetherm PRESSOSMART MP195NL Скачать руководство пользователя страница 23

23 

 

TECHNICIAN MENU 

This menu allows you to set: 

•

 Lack of water temporization, 

•

 Cascade temporization (if 2 pumps) 

•

 Stopping pumps temporization, 

•

 Filling tank temporization, 

•

 Low pressure alarm temporization, 

•

  Display language, 

•

 Reading event list, 

•

 Sensor scale correction 

•

 Relays tests into Autotest sub-menu 

 

 

ACTION 

 

 

DISPLAY 

Post lack of water temporization 

It is the temporization before activating pump(s) and after a lack of 
water default. 
Press + or 

– to modify the value, 

Press yellow 

 

for next line, 

 

NO WATER TEMPORISATION 

1 SEC. 

 

Cascade temporization (MP5 / MP7) 

Temporization to avoid the 2 pumps starting together 
Press + or 

– to modify the value, 

Press yellow 

 

for next line, 

 

CASCADING TEMPO. 

1 SEC. 

Stopping pump temporization (MP5/7) 

Temporization to avoid stopping the 2 pumps at the same time. 
Press + or 

– to modify the value, 

Press yellow 

 

for next line, 

 

STOP PUMP TEMPO. 

1 SEC. 

 

Filling temporization 

It  is  temporization  to  close  the  filling  electro  valve  when  the  correct 
water level has been reached inside the tank. 
Press + or 

– to adjust the value, 

Press yellow 

 

for next line, 

 

FILLING TEMPO. 

6 SEC. 

 

Low pressure alarm temporization 

If the pressure reaches the low alarm level, the alarm relay will only be 
powered on after a preset period of time. 
Press + or 

– to adjust this period, 

Press yellow 

 

for next line, 

 

LOW PRESS. TEMPO. 

1 SEC. 

 

Pumps cycling 

On 2 pumps units, you can set each pump working time P1/P2 
Press + or 

– to adjust the value, 

Press yellow 

 

for next line, 

 

SWAPPING TEMPO. 

10 MIN. 

NETWORK LEAKAGE parameters 

Press + to enter this sub-menu, 
Refer to page 24 hereafter, 
Press yellow 

 

for next line, 

 

LEAKAGE 

DETECTION 

 

Display Language 

Choose language used for display. 
Press + or 

– to select the required language, 

Press yellow 

 

for next line, 

 

LANGUAGE 

ENGLISH

 

Pressure recorder parameters 

This function is not used. Netherthless, it is possible to make trends or 
read values from a BMS using the Modbus optional card CI8021 
Press yellow 

 

for next line, 

 

RECORDER 

 
 

 

Press : 
 Yellow 

 and white 

 

to enter the menu. 

 Yellow 

 to get to the next frame/setting, 

 Yellow 

 to get to the previous frame/setting. 

Содержание PRESSOSMART MP195NL














































Отзывы:

Нет отзывов