CENTURION SYSTEMS VANTAGE 400 Скачать руководство пользователя страница 6

Страница: 6 / 44

page 6

www.CentSys.com

•

Never short-circuit the battery and do not try to recharge the batteries with power

supply units other than that supplied with the product, or manufactured by

Centurion Systems (Pty) Ltd

•

Make sure that the earthing system is correctly constructed, and that all metal parts

of the system are suitably earthed

• Safety devices must be fitted to the installation to guard against mechanical

movement risks such as crushing, dragging and shearing

• It is recommended that at least one warning indicator light be fitted to every system
• Always fit the warning signs visibly to the inside and outside of the gate
•

The installer must explain and demonstrate the manual operation of the gate in case

of an emergency, and must hand the User Guide/Warnings over to the user

•

The installer must explain these safety instructions to all persons authorised to use

this gate, and be sure that they understand the hazards associated with automated

gates

•

Do not leave packing materials (plastic, polystyrene, etc.) within reach of children as

such materials are potential sources of danger

•

Dispose of all waste products like packing materials, worn-out batteries etc, according

to local regulations

•

Always check the obstruction detection system, and safety devices for correct

operation

•

Neither Centurion Systems (Pty) Ltd, nor its subsidiaries, accept any liability caused

by improper use of the product, or for use other than that for which the automated

system was intended

•

This product was designed and built strictly for the use indicated in this

documentation; any other use, not expressly indicated here, could compromise the

service life/operation of the product and/or be a source of danger

• Everything not expressly specified in these instructions is not permitted

IMPORTA

AFETY

INS

TRUCTIONS

ETY

FIRST

Never run the operator directly from the battery!

Doing so will cause damage to the operator.

Only run the operator from the V-Series Controller.

Содержание VANTAGE 400













































Результаты поиска

Содержание VANTAGE 400

Отзывы:

Похожие инструкции для VANTAGE 400

Бренды по названию

Популярные бренды

CENTURION SYSTEMS VANTAGE 400, Руководство по механическому монтажу

Результаты поиска

Содержание VANTAGE 400

Отзывы:

Похожие инструкции для VANTAGE 400

Бренды по названию

Популярные бренды