Cedar Summit F25720 Скачать руководство пользователя страница 21

Страница: 21 / 108

1 x

Ladder Gap 1 x 4 x 21”

1 x

Rock Rail 1-3/8 x 2-1/2 x 57-53/64”

1 x

RW-AL Support 1 x 4 x 41-3/4”

024

025

023

Step 2: Access Ladder / Rockwall Assembly

Part 2

Wood Parts

Hardware

3 x

#8 x 2” Wood Screw

7 x

#8 x 1-3/8” Wood Screw

Fig. 2.3

S11

x 4

S11

x 3 in bottom holes

x 3 in top holes

S20

023

2-3/8” gap between top

Tread and Ladder Gap

025

Flush

020

024

021

022

Place (023) Ladder Gap on each access rail so there is a 2-3/8” gap between (023) Ladder Gap and the top

(022) Tread. Attach using 4 (S20) #8 x 1-3/8” Wood Screws. (fig. 2.3)

Place (024) Rock Rail on the ground next to (020) Left Access so it matches the orientation of the two access

rails as shown in fig. 2.3. Attach (025) RW-AL Support flush to the top of Access Ladder assembly and (024)

Rock Rail using 3 (S20) #8 x 1-3/8” Wood Screws in the top holes and 3 (S11) #8 x 2” Wood Screws in the

bottom holes. Pilot holes in (025) RW-AL Support should be centred over the rails. (fig. 2.3)

[email protected]

Содержание F25720













































































































Результаты поиска

Содержание F25720

Отзывы:

Бренды по названию

Популярные бренды

Cedar Summit F25720, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F25720

Отзывы:

Бренды по названию

Популярные бренды